105237-1310 ZEXEL 9 440 610 912 BOSCH SUPPLY PUMP 9440610912 1052371310 0424500130


 

Information supply pump

BOSCH 9 440 610 912 9440610912
ZEXEL 105237-1310 1052371310
MITSUBISHI-HEAV 0424500130 0424500130
105237-1310 SUPPLY PUMP
Rating:
17
Buy SUPPLY PUMP 105237-1310 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1. [1] 152000-9720 PUMP HOUSING
5. [1] 152100-1120 PUMP PLUNGER
6. [1] 152102-1300 COMPRESSION SPRING
7. [1] 152105-1500 CAPSULE
8. [1] 029332-6030 GASKET
10. [1] 152111-3221 TAPPET
10/2. [1] 152112-0500 ROLLER
10/3. [1] 152113-1000 BEARING PIN
10/4. [2] 152114-1600 SLIDER
14. [4] 152115-0200 VALVE BODY
14. [4] 152115-0200 VALVE BODY
15. [4] 152116-0200 COILED SPRING
15. [4] 152116-0200 COILED SPRING
16. [3] 152117-0100 CAPSULE
18. [4] 029331-6030 GASKET
18. [4] 029331-6030 GASKET
20. [1] 152121-0400 LOCKING WASHER
25. [1] 152200-5920 HAND PRIMER
30. [1] 152300-0120 EYE BOLT
32. [1] 029731-4680 EYE BOLT
35. [3] 029341-4130 GASKET D20&13.8T2*
36. [2] 029341-4130 GASKET D20&13.8T2*
42. [1] 152320-0100 COVER

Include in #1:

106871-2062 as SUPPLY PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
105237-1310 
9 440 610 912 
NP-FP/KD-P 
0424500130  MITSUBISHI-HEAV
SUPPLY PUMP
K 14GC FEED PUMP F/P




Information:

Solenoid Valve Replacement
Make reference to the at the beginning of the Testing And Adjusting section.
This procedure assumes that the ether cylinder mounted on the failed solenoid valve may still contain ether and is usable. If the ether cylinder is empty and needs replacement, complete this procedure and then follow the normal cylinder replacement procedure. See Ether Cylinder Replacement.
Solenoid Valve Assembly The solenoid valve itself is not serviceable. The complete solenoid valve assembly must be replaced. This includes the mounting bracket.1. Turn the disconnect switch to the OFF position. 2. Remove the ether cylinder from failed solenoid valve (1).3. Disconnect ether line (2) from the outlet of failed solenoid valve (1).4. Disconnect (unplug) solenoid valve harness connector (3). 5. Remove the reset switch bracket from the solenoid valve by removing two bolts (4). Leave the reset switch and wires intact on the bracket.6. Remove the solenoid valve assembly, which includes the mounting bracket, from the vehicle by removing two bolts (5).
Orifice Fitting And Filter7. Prepare the new solenoid valve for installation by installing a new orifice fitting and filter.
The orifice fitting has left-hand threads.
8. Attach the new solenoid valve and reset switch bracket to the vehicle. Tighten top two bolts (5) and leave lower two bolts (4) loose.
Gasket Filter9. Install a new gasket filter into the inlet of the solenoid valve.10. Install the same ether cylinder. See within Ether Cylinder Replacement. Hand tighten the ether cylinder to the solenoid valve. 11. Adjust the reset switch bracket such that reset switch button (6) depresses as much as possible while contacting the ether cylinder. Tighten lower two bolts (4) which fasten the reset switch bracket and solenoid valve to the vehicle. The reset switch must be adjusted correctly in order for the ether injection system to operate properly. The function of the reset switch is: to be OPEN (depressed switch button) when an ether cylinder is installed, and to be CLOSED (extended switch button) when the ether cylinder is removed. Ether injection is disabled when an ether cylinder is removed (reset switch closed).12. Verify that the reset switch is OPEN by continuity checking between the pin and socket in harness plug (7) of the reset switch. There should be no continuity.13. Reconnect the harnesses to the solenoid valve and the reset switch. Turn the disconnect switch to the ON position.Ether Cylinder Removal
Non-Empty Cylinders
During maintenance or servicing, the ether cylinders may need to be removed when they are not empty (for example, the cylinders may have to be removed to gain access to some other item requiring service). Under these conditions, it is desirable to remove and reinstall the ether cylinders without disturbing the "ether cylinder timers" within the ether injection control. This procedure allows the same ether cylinder to be reinstalled after it has been removed. Normal ether cylinder replacement is performed when the ether cylinder is empty. Normal removal of an empty ether cylinder resets the "ether cylinder timers" within the ether injection control. See Ether Cylinder Replacement. Failure to

Have questions with 105237-1310?





Group cross 105237-1310 ZEXEL

Mitsubishi 

 
ME066157 
SUPPLY PUMP
9 440 610 476 
 
SUPPLY PUMP

Mitsubishi-Heav 

105237-1310  
9 440 610 912 
NP-FP/KD-P 
0424500130 
SUPPLY PUMP
9 440 610 073 
 
SUPPLY PUMP
9 440 610 477 
 
SUPPLY PUMP

Isuzu 

F 01G 29R 00C 
1157500200 
SUPPLY PUMP
9 440 610 061 
1157500400 
SUPPLY PUMP
9 440 610 061 
1157500620 
SUPPLY PUMP

Hino 

 
225601421A 
SUPPLY PUMP
9 440 610 271 
NP-FP/KD-P 
225601422A 
SUPPLY PUMP
9 440 610 271 
NP-FP/KD-P 
225602530A 
SUPPLY PUMP

Isuzu 

 
1157500210 
SUPPLY PUMP
 
 
SUPPLY PUMP
 
 

Niigata-Urawa 

9 440 610 469 
NP-FP/KD-PS 
U2B48001A 
SUPPLY PUMP

Niigata-Tekkou 

9 440 610 469 
NP-FP/KD-PS 
U2B48001A 
SUPPLY PUMP
 
 

Isuzu 

9 440 610 306 
1157500270 
SUPPLY PUMP
Back to top