Buy 105220-6110 ZEXEL 9 440 610 157 BOSCH SUPPLY PUMP 9440610157 1052206110


 

Information supply pump

BOSCH 9 440 610 157 9440610157
ZEXEL 105220-6110 1052206110
105220-6110 SUPPLY PUMP
Rating:
71
Buy SUPPLY PUMP 105220-6110 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$89.67
 

18 Oct 2023

CN: MidzooUS
Fuel Pump 105220-6110 For Forklift
Generic Fuel Pump 105220-6110 For Forklift
$89.67
 

13 Dec 2022

CN: SuiParts
Fuel Pump 105220-6110 for Forklift
Generic Fuel Pump 105220-6110 For Forklift

You can express buy:

USD 60
02-08-2024

Scheme ###:

1. [1] 152003-1320 PUMP HOUSING
5. [1] 152100-1120 PUMP PLUNGER
6. [1] 152102-0400 COMPRESSION SPRING
7. [1] 152105-1500 CAPSULE
8. [1] 029332-6030 GASKET
10. [1] 152111-2820 TAPPET
10/2. [1] 152112-0100 ROLLER
10/3. [1] 152113-0700 BEARING PIN
10/4. [2] 152114-0400 SLIDER
14. [2] 152115-0500 VALVE BODY
14. [2] 152115-0500 VALVE BODY
15. [2] 152116-0200 COILED SPRING
15. [2] 152116-0200 COILED SPRING
17. [1] 152118-0900 ADAPTOR
18. [1] 029631-6060 O-RING
19. [1] 029631-6060 O-RING
20. [1] 152121-0200 LOCKING WASHER
25. [1] 152200-5420 HAND PRIMER
30. [1] 152300-6920 EYE BOLT
32. [1] 139814-0900 EYE BOLT
35. [2] 029341-4130 GASKET D20&13.8T2*
36. [2] 029341-4130 GASKET

Cross reference number

Zexel num
Bosch num
Firm num
Name
105220-6110 
9 440 610 157 
NP-FP/KS-AS 
   
SUPPLY PUMP
K




Information:

B. Back out (loosen) the lift adjustment screw 3/4 1/8of a turn.C. Put the nozzle in a vise with 8S2250 Holding Tool (1). Hold pressure adjusting screw (4) and tighten the locknut to a torque of 8.0-8.5 N m (70-75 lb in) using the 2P5487 Adapter (A). Recheck the opening pressure.Adjustment of 9L7883 Nozzles
1. Remove the nozzle from the tester and place in a vise using 8S2250 Nozzle Holding Tool (1). Loosen lift adjusting screw locknut (2). Loosen lift adjusting screw (3) two full turns counterclockwise.
If lift adjusting screw (3) is not loosened, the valve can be damaged in later steps.
2. Loosen pressure adjusting screw (4) and remove the nozzle from the nozzle holding tool. 3. Tilt the nozzle slightly down from the vertical position and remove pressure screw (4) and shims (5). If the shims do not come out of the nozzle, invert the nozzle and let the shims, spring and spring seat fall into the hand. If the valve comes out of its own weight, handle it carefully by its stem.4. To increase the opening pressure, add a 4N5730 Shim. The 4N5730 Shim is 0.13 mm (.005") thick and will increase the opening pressure approximately 1725 kPa (250 psi). A maximum of two shims can be added; if two shims do not increase opening pressure to specification given, discard the nozzle. 5. Assemble the nozzle, making sure the thickest shim (C) is against pressure screw (4). Put the nozzle in a vise using 8S2250 Nozzle Holding Tool (1). Tighten the pressure adjusting screw to 8.0-9.1 N m (70-80 lb in) torque.6. Remove the nozzle from the holding tool. Connect the nozzle, with the tip facing downward, to the tester. Point the nozzle tip into the 8S2270 Fuel Collector and the FT1384 Extension. Check the opening pressure and if it is not within specifications, repeat steps 4 and 5.Valve Lift Adjustment-9L7883 Nozzles
A. When the correct opening pressure is set, and while pumping test fluid through the nozzle, hold the lift adjusting screw locknut and slowly turn the lift adjusting screw clockwise (CW) until valve pressure rises 1380-3450 kPa (200-500 psi) above the nozzle opening pressure. Some test fluid may collect on the tip, but it must not flow at a rapid dribble.
Do not bend the valve by bottoming with too much force.
B. Back out the lift screw 3/4 1/8 turn, hold the lift adjusting screw, and tighten the locknut just enough so the screw will not turn; the lift is now set. C. Put the nozzle in a vise using 8S2250 Holding Tool (1). Tighten the locknut to 4.0-4.5 N m (35-40 lb in). Recheck valve opening pressure.Adjustment of 9L6969, 7N0449, 9N3299, 9N3700, 9N3979, 1W5829, 4W1819, 4W8483 and 7W3710 Nozzles
1. Put the nozzle in a vise using the 8S2250 Holding Tool (1). Loosen lift adjusting screw locknut (2). Turn lift adjusting screw (3) two full turns counterclockwise (CCW). 2. Hold lift adjusting screw (3) with a .08 mm (5/64") hex wrench (4) and

Have questions with 105220-6110?





Group cross 105220-6110 ZEXEL

 
 

105220-6110  
9 440 610 157 
NP-FP/KS-AS 
 
SUPPLY PUMP
 
 

9 440 610 414 
NP-FP/KS-A 
 
SUPPLY PUMP

Isuzu 

9 440 610 445 
8970744430 
SUPPLY PUMP

Mitsubishi 

9 440 610 273 
NP-FP/KS-A 
ME730911 
SUPPLY PUMP

Nissan-Diesel 

9 440 610 898 
NP-FP/KS-A 
166400T860 
SUPPLY PUMP
9 440 610 576 
 
SUPPLY PUMP

Isuzu 

9 440 610 446 
8970843480 
SUPPLY PUMP
9 440 610 447 
 
SUPPLY PUMP

Isuzu 

9 440 610 447 
8970818040 
SUPPLY PUMP
Back to top