Buy 105220-5360 ZEXEL 9 440 610 409 BOSCH SUPPLY PUMP 9440610409 1052205360


 

Information supply pump

BOSCH 9 440 610 409 9440610409
ZEXEL 105220-5360 1052205360
105220-5360 SUPPLY PUMP
Rating:
80
Buy SUPPLY PUMP 105220-5360 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$79.99

03 Jan 2025
2.0[0.90] pounds
CN: Meckparts
Meckparts Fuel Lift Pump 105220-5360 105220 5360 Compatible With Komatsu Industrial Equipment D921
Meckparts Part Numbers: 105220-5360 105220 5360 || Compatible With Komatsu Industrial Equipment D921 || Package Includes: 1x Fuel Lift Pump || Easy To Install. Manufactured To Precise OE Requirements For Perfect Fit. Reliable Performance. || Replacement Parts. As Good As OEM At A Fraction Of The Price. Exact Same Performance As Original.
$80.00
 

08 May 2023

CN: YEM PARTS
YANNAL PART Fuel Lift Pump 105220-5360 For Komatsu D921 Industrial Equipment
YANNAL PART

Scheme ###:

1. [1] 152003-1020 PUMP HOUSING
5. [1] 152100-1120 PUMP PLUNGER
6. [1] 152102-1600 COMPRESSION SPRING
7. [1] 152105-1500 CAPSULE
8. [1] 029332-6030 GASKET
10. [1] 152111-2820 TAPPET
10/2. [1] 152112-0100 ROLLER
10/3. [1] 152113-0700 BEARING PIN
10/4. [2] 152114-0400 SLIDER
14. [2] 152115-0500 VALVE BODY
14. [2] 152115-0500 VALVE BODY
15. [2] 152116-0200 COILED SPRING
15. [2] 152116-0200 COILED SPRING
17. [1] 152118-0900 ADAPTOR
18. [1] 029631-6060 O-RING
19. [1] 029631-6060 O-RING
20. [1] 152121-0200 LOCKING WASHER
25. [1] 152200-5420 HAND PRIMER
30. [1] 152300-5920 EYE BOLT
32. [1] 029731-4680 EYE BOLT
33. [1] 152350-6720 PIPE
35. [2] 029341-4130 GASKET D20&13.8T2*
35. [2] 029341-4130 GASKET D20&13.8T2*
36. [2] 029341-4130 GASKET D20&13.8T2*
42. [1] 152320-0100 COVER

Cross reference number

Zexel num
Bosch num
Firm num
Name
105220-5360 
9 440 610 409 
NP-FP/KS-A 
   
SUPPLY PUMP
K 14GC FEED PUMP F/P




Information:

Cooling System
Never add coolant to an overheated engine; allow the engine to cool first.Check the specific gravity of the antifreeze coolant solution frequently in cold weather to ensure adequate protection.If the machine is to be stored in, or shipped to, an area with below freezing temperatures; the cooling system must be protected against freezing to the lowest expected outside temperature.All water is corrosive at engine operating temperature. The cooling system should be protected with conditioner at all times regardless of the concentration of antifreeze. This can be done by using Caterpillar coolant conditioner elements. Use a precharge element when filling the system or changing coolant. Install a new maintenance element every 250 service hours during operation.Do not use Caterpillar coolant conditioner elements with Dowtherm 209 Full-Fill coolant. Follow the instructions provided with the Dowtherm 209 Full-Fill coolant.
Coolant should be drained and replaced every 2000 service hours or 1 year. However, when coolant conditioner maintenance elements are replaced every 250 service hours as recommended, the drain period can be extended to 4000 service hours or 2 years. If your engine does not use coolant conditioner elements, see "Cooling System" under "Maintenance Recommendations" in your Maintenance (Lubrication and Maintenance) Guide.Premix antifreeze coolant solution to provide protection to the lowest expected outside temperature. Pure undiluted antifreeze will freeze at -23°C (-10°F).Use clean water that is low in scale forming mineral. Do not use softened water.Filling at over 20 liters (5 U.S. gallons) per minute can cause air pockets in the cooling system.After draining and refilling the cooling system, start and operate the engine with the fill cap off until the coolant level stabilizes. Add coolant as necessary to fill the system.When the engine is shipped from the factory, its cooling system is protected to -28°C (-20°F), with permanent-type antifreeze.Operate with a thermostat in the cooling system year-round. Overheating can arise without a thermostat.Fuel System
Fill the fuel tank at the end of each day of operation to drive out moist air and to prevent condensation. Do not fill the tank to the top. The fuel expands as it gets warm and may overflow.
Do not fill the fuel filters with fuel before installing them. Contaminated fuel will cause accelerated wear to the fuel system parts.
Check the fuel level with the dipstick in the filler opening. Drain the water and sediment from the fuel tank at the start of a shift or after the fuel tank has been filled and allowed to stand for 5 to 10 minutes.After changing the fuel filters, always bleed the fuel system to remove air bubbles from the system.Drain water and sediment from any fuel storage tank weekly, and before the tank is refilled. This will help prevent water or sediment from being pumped from the storage tank into the machine fuel tank.Use only fuel as recommended in the 'Fuel, Coolant and Lubricant" section of this Guide.

Have questions with 105220-5360?





Group cross 105220-5360 ZEXEL

Hino 

9 440 610 067 
NP-FP/KS-AS 
225601530A 
SUPPLY PUMP
9 440 610 067 
NP-FP/KS-AS 
225601630A 
SUPPLY PUMP
9 440 610 067 
NP-FP/KS-AS 
S225601630 
SUPPLY PUMP
 
 

Isuzu 

9 440 610 693 
8944698580 
SUPPLY PUMP
9 440 610 943 
NP-FP/KS-AS 
 
SUPPLY PUMP

Nissan-Diesel 

9 440 611 048 
1664095002 
SUPPLY PUMP

Mitsubishi 

9 440 610 895 
NP-FP/KS-AS 
ME722908 
SUPPLY PUMP
105220-5360  
9 440 610 409 
NP-FP/KS-A 
 
SUPPLY PUMP

Hino 

9 440 610 896 
NP-FP/KS-A 
225601680A 
SUPPLY PUMP
 
 
SUPPLY PUMP
9 440 611 016 
NP-FP/KS-AS 
 
SUPPLY PUMP
9 440 610 748 
 
SUPPLY PUMP
Back to top