105217-1411 ZEXEL 9 440 610 710 BOSCH SUPPLY PUMP 9440610710 1052171411 1664097001

Information supply pump

BOSCH 9 440 610 710 9440610710

ZEXEL 105217-1411 1052171411

NISSAN-DIESEL 1664097001 1664097001

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy SUPPLY PUMP 105217-1411 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	152000-4620	PUMP HOUSING
5.	[1]	152100-1120	PUMP PLUNGER
6.	[1]	152102-0400	COMPRESSION SPRING
7.	[1]	152105-1500	CAPSULE
8.	[1]	029332-6030	GASKET
10.	[1]	152111-3221	TAPPET
10/2.	[1]	152112-0500	ROLLER
10/3.	[1]	152113-1000	BEARING PIN
10/4.	[2]	152114-1600	SLIDER
14.	[2]	152115-0200	VALVE BODY
14.	[2]	152115-0200	VALVE BODY
15.	[2]	152116-0200	COILED SPRING
15.	[2]	152116-0200	COILED SPRING
16.	[1]	152117-0400	CAPSULE
18.	[2]	029331-6030	GASKET
18.	[2]	029331-6030	GASKET
20.	[1]	152121-0200	LOCKING WASHER
25.	[1]	152200-5620	HAND PRIMER
30.	[1]	152300-6020	EYE BOLT
32.	[1]	029731-4680	EYE BOLT
35.	[2]	026514-1840	GASKET D17.9&14.2T1
36.	[2]	026514-1840	GASKET D17.9&14.2T1

Include in #1:

106861-0641 as SUPPLY PUMP

106861-0711

106861-0820

Cross reference number

Zexel num

Bosch num

Firm num

Name

105217-1411

9 440 610 710

1664097001 NISSAN-DIESEL

SUPPLY PUMP
* K 14GC FEED PUMP F/P

Information:

This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS5562" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.
Termination Date
December 31, 1999Problem
The connection plate from the fuel injection pump lever may wear prematurely causing the return spring to disconnect on certain 307 Excavators. When the return spring disconnects, the fuel injection pump will no longer operate properly.
Affected Product
Model & Identification Number
307 (2WM96-1002)
Parts Needed
1 - 5C2890 Nut1 - 8T4138 Bolt2 - 9X8256 Washer1 - 1393951 Strip1 - 1643187 PlateAction Required
See the attached Rework Procedures.
Service Claim Allowances
This is a 0.5-hour job.
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.(1-Rework Procedure)Rework Procedure
1. Disconnect 3W6485 Spring from both sides.2. Unscrew 8T4134 Nut, remove 9X8256 Washer and 1190312 Plate, put back in place 9X8256 Washer and 8T4134 Nut. (Refer to Illustration 1).3. Install 1393951 Strip using existing bolt located on top left side of the 6I0835 Front Housing. The strip must be oriented so to be aligned with the spring which will be connected to the lever. See Illustration 2.4. Install the new 1643187 Plate against the pump lever, using the hole which is below the connection to the governor cable. 8T4138 Bolt goes through 9X8256 Washer, 1643187 Plate, pump lever, 9X8256 Washer and 5C2890 Nut. Refer to Illustrations 3 and 4.5. Connect 3W6485 Spring to 1393951 Strip and 1643187 Plate. Refer to Illustrations 2 and 3)
Illustration 1
Illustration 2
Illustration 3
Illustration 4