Buy 105210-6380 ZEXEL 9 440 610 616 BOSCH SUPPLY PUMP 9440610616 1052106380 8972243960


 

Information supply pump

BOSCH 9 440 610 616 9440610616
ZEXEL 105210-6380 1052106380
ISUZU 8972243960 8972243960
105210-6380 SUPPLY PUMP
Rating:
28
Buy SUPPLY PUMP 105210-6380 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$72.32
 

09 Mar 2023

CN: MidzooUS
Fuel Feed Pump 105210-6380 for Excavator
Generic Fuel Feed Pump 105210-6380 for Excavator
$73.05
 

28 Nov 2022

CN: SuiParts
Fuel Feed Pump 105210-6380 for Excavator
Generic Fuel Feed Pump 105210-6380 for Excavator
$115.00
 

28 Jul 2022

CN: HOLDWELL-US
Holdwell Fuel Feed Pump 105210-6380 compatible with Isuzu Excavator
HOLDWELL Fuel Feed Pump 105210-6380

You can express buy:

USD 30
01-04-2024
Fuel Feed Pump 105210-6380 for Isuzu Excavator

Scheme ###:

1. [1] 152061-0120 PUMP HOUSING
2. [1] 152030-0300 STOP PIN
5. [1] 152100-2301 PUMP PLUNGER
6. [1] 152102-0400 COMPRESSION SPRING
7. [1] 152105-1500 CAPSULE
8. [1] 139526-0000 GASKET
14. [2] 152115-0500 VALVE BODY
14. [2] 152115-0500 VALVE BODY
15. [2] 152116-0200 COILED SPRING
15. [2] 152116-0200 COILED SPRING
16. [1] 152118-0900 ADAPTOR
18. [2] 029631-6060 O-RING
18. [2] 029631-6060 O-RING
25. [1] 152200-6720 HAND PRIMER
32. [1] 029111-4050 CAPSULE
36. [1] 026514-2040 GASKET

Cross reference number

Zexel num
Bosch num
Firm num
Name
105210-6380 
9 440 610 616 
NP-FP/KEP-AD 
8972243960  ISUZU
SUPPLY PUMP
K 14GC FEED PUMP F/P




Information:

(a) When regrinding journals of the crankshaft, be sure to refinish all journals to the same dimension.(b) Finish the fillet radius to R3 0.2 mm [0.1181 0.0079 in.].
Inspection of Oil Seal Contact Surface
Check the oil seal contact surface of the crankshaft back-end, and, if the crankshaft face has been excessively worn by the oil seal, replace the oil seal and oil sleeve with replacement parts.
Inspection of oil seal contact surface(1) Installation of oil seal sleeveTo install the oil seal sleeve, coat the inner surface of the sleeve with oil, and use the crankshaft sleeve installer for driving the sleeve into place.
Be careful not to dent or scratch the outer surface of the oil seal sleeve.
When the oil seal slinger becomes worn after engine operation, remove the oil seal sleeve by following the procedure below, and replace it with a replacement oil seal assembly (oil seal and oil seal sleeve).
Inspection of oil seal sleeve
Inspection of oil seal contact surface(2) Removal of oil seal sleeveAt three locations on the sleeve end face, hold a chisel at a right angle to the sleeve and strike with a hammer, and remove the sleeve when it becomes loose.If this method does not allow the removal of the sleeve, hold the chisel in the axial direction and lightly tap to expand and loosen the sleeve.
Be careful not to damage the crankshaft with the chisel when removing the oil seal sleeve.
Removal of oil seal sleeveMeasurement of Crankshaft Runout
Support the crankshaft on its front and rear journals in V-blocks, and measure the runout at the center journal with a dial gage. Compare the amount of runout with the standard. If the runout is small, correct by grinding. If the runout is large, straighten with a press.If the runout exceeds the limit significantly, replace the crankshaft.
Measurement of crankshaft runoutRemoval of Crankshaft Gear
Use the gear puller to remove the crankshaft gear. Do not remove the crankshaft gear unless the crankshaft or gear is replaced.
Removal of crankshaft gearInstallation of Crankshaft Gear
(1) Heat the gear to a temperature of 100 to 150 °C [212 to 302 °F].(2) Install the key to the crankshaft.(3) Align the gear with key and insert the gear fully.
Installation of crankshaft gearMeasurement of Cylinder Bore
(1) Using a cylinder gage, measure the cylinder bore and cylindricity. If the limit value is exceeded even at one place, bore all cylinders and replace the pistons and piston rings with oversize pistons and piston rings. Measure at three locations each in directions A and B shown in the diagram.
Measurement of inside diameter of cylinder(2) Boring of cylinders(a) Since there are two piston oversizes (0.25 mm [0.0098 in.] and 0.50 mm [0.0197 in.] oversize) as indicated above, determine the appropriate piston size to be used based on the largest cylinder bore diameter.(b) Measure the outside diameter of the piston to be used. The piston diameter measuring points are shown in the diagram.(c) Based on the measurements of the piston outside diameter, calculate the finishing dimension to be achieved by

Have questions with 105210-6380?





Group cross 105210-6380 ZEXEL

Hino 

9 440 610 218 
NP-FP/KEP-AD 
225602550A 
SUPPLY PUMP
9 440 610 500 
NP-FP/KEP-AD 
 
SUPPLY PUMP

Hino 

9 440 610 602 
NP-FP/KEP-AD 
225602570A 
SUPPLY PUMP
9 440 610 501 
NP-FP/KEP-A 
 
SUPPLY PUMP

Mazda 

9 440 610 502 
NP-FP/KEP-AD 
TF7013VF0A 
SUPPLY PUMP
9 440 610 503 
NP-FP/KEP-A 
 
SUPPLY PUMP
 
 

Isuzu 

9 440 610 615 
NP-FP/KEP-A 
8972232890 
SUPPLY PUMP
105210-6380  
9 440 610 616 
NP-FP/KEP-AD 
8972243960 
SUPPLY PUMP
9 440 610 657 
NP-FP/KEP-AD 
 
SUPPLY PUMP
Back to top