Information supply pump
BOSCH
9 440 610 431
9440610431
ZEXEL
105210-5430
1052105430
ISUZU
8971675600
8971675600
Rating:
Scheme ###:
| 1. | [1] | 152051-0520 | PUMP HOUSING |
| 5. | [1] | 152100-1120 | PUMP PLUNGER |
| 6. | [1] | 152102-0400 | COMPRESSION SPRING |
| 7. | [1] | 152105-1500 | CAPSULE |
| 8. | [1] | 029332-6030 | GASKET |
| 10. | [1] | 152111-2820 | TAPPET |
| 10/2. | [1] | 152112-0100 | ROLLER |
| 10/3. | [1] | 152113-0700 | BEARING PIN |
| 10/4. | [2] | 152114-0400 | SLIDER |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 16. | [1] | 152118-0900 | ADAPTOR |
| 18. | [1] | 029631-6060 | O-RING |
| 19. | [1] | 029631-6060 | O-RING |
| 20. | [1] | 152121-0200 | LOCKING WASHER |
| 25. | [1] | 152200-5420 | HAND PRIMER |
| 30. | [1] | 152300-5620 | EYE BOLT |
| 32. | [1] | 029111-4050 | CAPSULE |
| 33. | [1] | 152350-6620 | PIPE |
| 35. | [2] | 029341-4080 | GASKET |
| 36. | [2] | 029341-4080 | GASKET |
| 49. | [1] | 029731-4580 | EYE BOLT |
| 51. | [1] | 026514-2040 | GASKET |
Include in #1:
101402-4270
as SUPPLY PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
1. Exploded viewsIn the exploded views, the component parts are separated but so arranged to show their relationship to the whole. Index numbering is used to identify the parts and to indicate a sequence in which the parts are to be removed for disassembly, or they are to be installed for assembly. 2. SymbolsThe following symbols are used in this manual to emphasize important and critical instructions:
Indicates a condition that is essential to highlight.
Indicates a condition that can cause engine damage.
Indicates a condition that can cause personal injury or death.3. Definition of locational termsThe fan end is "front" and the flywheel end is "rear". The words "left" and "right" are as these directions would appear from the flywheel end.4. Dimensional or specification termsNominal size...Is the named size which has no specified limits of accuracy.Standard...Is the dimension of a part to be attained at the time of assembly, or the standard performance.Limit...Is the maximum or minimum permissible limit beyond which a part must be repaired or replaced.5. Tightening torquesTighten bolts, nuts, etc. in a wet condition (apply oil to threads) when specified as [WET]. Tighten them in a dry condition unless so specified. Use the general torques unless otherwise specified.MODEL IDENTIFICATION AND SERIAL NUMBER LOCATION
1. Model identification location(a) The model identification is embossed on the right side of the cylinder block, near the fuel injection pump mount.(b) The model identifications and displacements of the engines in current production are as listed below:
Model identification location(c) A scheme of coding used for identifying the engines in current production is as follows:
Example: Coded designation2. Serial Number LocationThe serial number is punched on the cylinder block, near the fuel injection pump mount.
Serial number locationCOMPONENT LOCATION
S3L/S3L2 S4L/S4L2SPECIFICATIONS
PERFORMANCE CURVES (ONE-HOUR RATING, WITH FAN)
PRIME POWER OUTPUT CHART
Indicates a condition that is essential to highlight.
Indicates a condition that can cause engine damage.
Indicates a condition that can cause personal injury or death.3. Definition of locational termsThe fan end is "front" and the flywheel end is "rear". The words "left" and "right" are as these directions would appear from the flywheel end.4. Dimensional or specification termsNominal size...Is the named size which has no specified limits of accuracy.Standard...Is the dimension of a part to be attained at the time of assembly, or the standard performance.Limit...Is the maximum or minimum permissible limit beyond which a part must be repaired or replaced.5. Tightening torquesTighten bolts, nuts, etc. in a wet condition (apply oil to threads) when specified as [WET]. Tighten them in a dry condition unless so specified. Use the general torques unless otherwise specified.MODEL IDENTIFICATION AND SERIAL NUMBER LOCATION
1. Model identification location(a) The model identification is embossed on the right side of the cylinder block, near the fuel injection pump mount.(b) The model identifications and displacements of the engines in current production are as listed below:
Model identification location(c) A scheme of coding used for identifying the engines in current production is as follows:
Example: Coded designation2. Serial Number LocationThe serial number is punched on the cylinder block, near the fuel injection pump mount.
Serial number locationCOMPONENT LOCATION
S3L/S3L2 S4L/S4L2SPECIFICATIONS
PERFORMANCE CURVES (ONE-HOUR RATING, WITH FAN)
PRIME POWER OUTPUT CHART