Information supply pump
BOSCH
9 440 610 427
9440610427
ZEXEL
105210-5330
1052105330
ISUZU
8970811820
8970811820
Rating:
Scheme ###:
| 1. | [1] | 152051-0920 | PUMP HOUSING |
| 5. | [1] | 152100-1120 | PUMP PLUNGER |
| 6. | [1] | 152102-0400 | COMPRESSION SPRING |
| 7. | [1] | 152105-1500 | CAPSULE |
| 8. | [1] | 139526-0000 | GASKET |
| 10. | [1] | 152111-2820 | TAPPET |
| 10/2. | [1] | 152112-0100 | ROLLER |
| 10/3. | [1] | 152113-0700 | BEARING PIN |
| 10/4. | [2] | 152114-0400 | SLIDER |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 16. | [1] | 152118-0900 | ADAPTOR |
| 18. | [1] | 029631-6060 | O-RING |
| 19. | [1] | 029631-6060 | O-RING |
| 20. | [1] | 152121-0200 | LOCKING WASHER |
| 25. | [1] | 152200-5420 | HAND PRIMER |
| 30. | [1] | 152300-5620 | EYE BOLT |
| 32. | [1] | 029111-4050 | CAPSULE |
| 33. | [1] | 152350-7820 | PIPE |
| 35. | [2] | 029341-4080 | GASKET |
| 36. | [2] | 029341-4080 | GASKET |
| 49. | [1] | 029731-4580 | EYE BOLT |
| 51. | [1] | 026514-2040 | GASKET |
Include in #1:
101491-0700
as SUPPLY PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Essential Tools (For John Deere Starting Motor)
Commutator and Drive End Bushing Tools
Fig. 137-End Drive Bushing Removal and Installation Tool1 - 27487 - Handle - For removing and installing commutator and drive end bushings.2 - 27494 - Disk - For removing commutator and drive end bushing.27495 - Disk - For installing commutator and drive end bushing.3 - 27491 and 27492 - Disk Spacer - For removing and installing commutator and drive end bushing.4 - 27493 - Disk Pilot - For removing and installing commutator and drive end bushing.Center Bushing and Oil Seal Tools
Fig. 138-Center Bushing and Oil Seal Tools1 - 27487 - Handle - For installing center bushing and oil seal.2 - 27505 - Disk - For installing center bushing.3 - 27512 - Disk - For installing center oil seal.4 - 27501 - Disk Pilot - For installing center bushing and oil seal.JDE-80 - Starter Wrench - To remove and install rear mounting nut on starting motor.
Fig. 139-Starter WrenchConvenience Tools (For a Delco-Remy Starter)
Fig. 140-Armature Commutator Turning and Undercut ToolArmature Commutator Turning and Undercut Tool-Used to undercut armature and commutator.
Fig. 141-Pre-Lubricated Bushing ArborPre-Lubricated Bushing Arbor-To install prelubricated bushings.
Fig. 142-Spring Tension GaugeSpring Tension Gauge-To check brush spring tension.
Commutator and Drive End Bushing Tools
Fig. 137-End Drive Bushing Removal and Installation Tool1 - 27487 - Handle - For removing and installing commutator and drive end bushings.2 - 27494 - Disk - For removing commutator and drive end bushing.27495 - Disk - For installing commutator and drive end bushing.3 - 27491 and 27492 - Disk Spacer - For removing and installing commutator and drive end bushing.4 - 27493 - Disk Pilot - For removing and installing commutator and drive end bushing.Center Bushing and Oil Seal Tools
Fig. 138-Center Bushing and Oil Seal Tools1 - 27487 - Handle - For installing center bushing and oil seal.2 - 27505 - Disk - For installing center bushing.3 - 27512 - Disk - For installing center oil seal.4 - 27501 - Disk Pilot - For installing center bushing and oil seal.JDE-80 - Starter Wrench - To remove and install rear mounting nut on starting motor.
Fig. 139-Starter WrenchConvenience Tools (For a Delco-Remy Starter)
Fig. 140-Armature Commutator Turning and Undercut ToolArmature Commutator Turning and Undercut Tool-Used to undercut armature and commutator.
Fig. 141-Pre-Lubricated Bushing ArborPre-Lubricated Bushing Arbor-To install prelubricated bushings.
Fig. 142-Spring Tension GaugeSpring Tension Gauge-To check brush spring tension.