105118-7060 ZEXEL 9 430 612 699 BOSCH NOZZLE AND HOLDER ASSY. 9430612699 1051187060 10115150001


 

Information nozzle and holder assy.

BOSCH 9 430 612 699 9430612699
ZEXEL 105118-7060 1051187060
TOYO-SHA 10115150001 10115150001
105118-7060 NOZZLE AND HOLDER ASSY.
Rating:
43
Buy NOZZLE AND HOLDER ASSY. 105118-7060 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104139-3000 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105118-7060 
9 430 612 699 
48-2030B 
10115150001  TOYO-SHA
NOZZLE AND HOLDER ASSY.
BD162 * K 53KQ NOZZLE & HOLDER ASSY N&NH KBDL2,1-P N&NH




Information:

Start By:a. remove automatic timing advance unit
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
Before any timing gears are removed, make sure "C" on the crankshaft gear is in alignment with "C" mark on the camshaft gear. 1. Remove bolts, plate (1) and fuel pump idler gear (2). 2. Remove bearing from idler gear (2) with tool (A). 3. Remove four bolts (3) and camshaft gear (4). 4. Remove bolts that are used to fasten shield (5) in position between the fuel pump and the exhaust manifold. Slide shield back from the timing cover plate.5. Remove the three nuts (6). 6. Remove six bolts (7). Remove the timing gear plate and the gasket. The following steps are to install the timing gears and plate.7. Clean the old gasket from the contact surfaces of the timing gear plate and cylinder block. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block.8. Be sure the O-ring seals are in position on the end of the fuel injection pump housing. Put the timing gear plate in position on the cylinder block and install the six bolts (7). Install nuts (6).
After the timing gear plate is installed, be sure the rack is free to move in the fuel injection pump housing. The O-ring seal on the drive end of the fuel injection pump housing can hold the rack and prevent free rack movement. Rack movement can be seen through hole in the timing gear plate just above where the fuel pump gear is mounted. If the rack does not move freely, remove the timing gear plate and check the O-ring seal on the drive end of the fuel injection pump housing. If the rack does not move freely, the engine can over speed and be damaged. Serious personal injury can be the result.
9. Install camshaft gear (4) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear as shown in the illustration in the Specification section of this manual. Tighten the volts to a torque of 55 7 N m (41 5 lb ft).10. Use tooling (A) to install the bearing in idler gear (2). The end of the bearing must be 1.52 .025 mm (.060 .010 in) below the face of the gear hub.11. Be sure the oil hole in the shaft for gear (2) is open. Install idler gear (2). Put the plate on position with the finished side toward gear (2) and install the bolts.12. Install shield (5) and the four bolts.End By:a. install automatic timing advance unit

Have questions with 105118-7060?





Group cross 105118-7060 ZEXEL

Isuzu 

 
8944743892 
NOZZLE AND HOLDER ASSY.
4JB1
9 430 610 062 
48-2030C 
8944743893 
NOZZLE AND HOLDER ASSY.
4JB1
9 430 612 696 
48-2031C 
8944743894 
NOZZLE AND HOLDER ASSY.
4JB1

Honda 

9 430 613 141 
 
NOZZLE AND HOLDER ASSY.
ZG3
9 430 610 067 
48-2080G3 
 
NOZZLE AND HOLDER ASSY.

Honda 

9 430 610 072 
48-2081G3 
16410ZG30130 
NOZZLE AND HOLDER ASSY.
ZG4
9 430 612 697 
48-2080G5 
16410ZG50030 
NOZZLE AND HOLDER ASSY.
ZG5

Isuzu 

9 430 613 142 
48-2030A 
8943280901 
NOZZLE AND HOLDER ASSY.
4JB1-TC
9 430 610 069 
48-2090 
8943280902 
NOZZLE AND HOLDER ASSY.
9 430 610 151 
48-2031H 
8943280903 
NOZZLE AND HOLDER ASSY.
4JB1-TC

Toyo-Sha 

9 430 612 698 
48-2030E 
10015150001 
NOZZLE AND HOLDER ASSY.
BD151
105118-7060  
9 430 612 699 
48-2030B 
10115150001 
NOZZLE AND HOLDER ASSY.
BD162
9 430 612 700 
48-2080A 
 
NOZZLE AND HOLDER ASSY.

Honda 

9 430 610 099 
48-2081A 
16410ZG50230 
NOZZLE AND HOLDER ASSY.
ZG5
9 430 610 100 
48-2081E3 
16410ZG38010 
NOZZLE AND HOLDER ASSY.
ZG3
9 430 610 100 
48-2081E3 
16410ZG38012M1 
NOZZLE AND HOLDER ASSY.
ZG3

Fuji-Heavy 

9 430 612 701 
48-2100 
2286320200 
NOZZLE AND HOLDER ASSY.
DY41
Back to top