105110-4440 ZEXEL 9 430 611 799 BOSCH NOZZLE AND HOLDER ASSY. 9430611799 1051104440 100219290


 

Information nozzle and holder assy.

BOSCH 9 430 611 799 9430611799
ZEXEL 105110-4440 1051104440
SHINKO-ENGIN. 100219290 100219290
105110-4440 NOZZLE AND HOLDER ASSY.
Rating:
64
Buy NOZZLE AND HOLDER ASSY. 105110-4440 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

106682-4680 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105110-4440 
9 430 611 799 
40-2200A 
100219290  SHINKO-ENGIN.
NOZZLE AND HOLDER ASSY.
S12V15D K 53KN NOZZLE & HOLDER ASSY N&NH KBALS N&NH




Information:

Start By:a. disassemble governorb. remove fuel injection pumps 1. Remove cover (1) from the fuel injection pump housing. 2. Remove rack (2) from the fuel injection pump housing.
If the original lifters are to be installed in the fuel injection pump housing, put identification marks on them as to their location in the housing.
3. Remove lifters (3) from the fuel injection pump housing. 4. Put the fuel injection pump housing on end on blocks, and use Tool (A) to remove snap ring (4) from the camshaft. 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5) on the camshaft. Remove washer (5). 6. Remove camshaft (6) from the fuel injection pump housing. 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear and put clean engine oil on all parts before assembly.1. Use Tool (A) to install bearing (2) in the governor end of the fuel injection pump housing with joint (3) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (.010 0.008 in) below the surface of the housing.2. Use Tool (A) to install bearing (1) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (0.282 0.005 in) below the surface of the housing. 3. Use Tool (A) to install bearing (4) in the drive end of the fuel injection pump housing with the joint in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (0.039 0.010 in) below the surface of the housing. 4. Install plate assembly (6) of Tool (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (5) of Tool (C). Install the driver and bearing in plate assembly (6) with the groove in the driver in alignment with the pin in the plate. Use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate assembly (6).5. Remove Tool (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in) below the surface of the housing. 6. Install camshaft (7) in the fuel injection pump housing.7. Put the fuel injection pump housing on end, and put a block under the camshaft. 8. Put washer (9) over the end of the camshaft, and use Tool (A) and a spacer (8) that has an inside diameter of 38.1 mm (1.5 in) and a length of 31.75 mm (1.25 in) to push the washer

Have questions with 105110-4440?





Group cross 105110-4440 ZEXEL

Isuzu 

9 430 612 769 
1153002860 
NOZZLE AND HOLDER ASSY.
6WA1
9 430 611 798 
41-3010H 
 
NOZZLE AND HOLDER ASSY.

Shinko-Engin. 

9 430 612 768 
100219300 
NOZZLE AND HOLDER ASSY.
S12V15D
105110-4440  
9 430 611 799 
40-2200A 
100219290 
NOZZLE AND HOLDER ASSY.
S12V15D

Isuzu 

9 430 611 800 
41-3070N 
1153003050 
NOZZLE AND HOLDER ASSY.
6WA1TCN
9 430 611 801 
41-3070N 
1153003051 
NOZZLE AND HOLDER ASSY.
6WA1TCN
9 430 611 802 
41-3071N 
1153003530 
NOZZLE AND HOLDER ASSY.
6WA1TCN
9 430 611 803 
41-3072N 
1153003531 
NOZZLE AND HOLDER ASSY.
6WA1TCN
9 430 611 804 
41-3080C 
1153003060 
NOZZLE AND HOLDER ASSY.
6WA1TCS
9 430 611 805 
41-4090Y 
1153003151 
NOZZLE AND HOLDER ASSY.
6SD1TC
9 430 611 806 
41-4090Y 
1153003152 
NOZZLE AND HOLDER ASSY.
6SD1TC
9 430 611 807 
41-3100J4 
 
NOZZLE AND HOLDER ASSY.

Nissan-Diesel 

9 430 611 808 
41-3101J4 
1660097105 
NOZZLE AND HOLDER ASSY.
D9XC
Back to top