105040-2200 ZEXEL 9 430 615 424 BOSCH NOZZLE-HOLDER 9430615424 1050402200 0170990830


 

Information nozzle-holder

BOSCH 9 430 615 424 9430615424
ZEXEL 105040-2200 1050402200
SHINKO-ENGIN. 0170990830 0170990830
105040-2200 NOZZLE-HOLDER
Rating:
29
Buy NOZZLE-HOLDER 105040-2200 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

4. [1] 150550-3700 STOP PIN
6. [1] 150562-1600 COMPRESSION SPRING
8. [1] 150565-2300 THREADED PIN
10. [1] 150567-7400 CAP NUT
11. [1] 029331-6030 GASKET
13. [1] 150524-3600 SPACER BUSHING
20. [1] 150650-8800 NOZZLE-RETAINING NUT
21. [1] 029300-5070 GASKET D12&5T1
22. [1] 150646-0200 INLET UNION

Include in #1:

106682-4680 as NOZZLE-HOLDER

Cross reference number

Zexel num
Bosch num
Firm num
Name
105040-2200 
9 430 615 424 
0170990830  SHINKO-ENGIN.
NOZZLE-HOLDER
K




Information:

start by:a) remove pistons 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove the piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS, SPECIAL INSTRUCTIONS, Form No. SMHS7295.5. Heat the connecting rod (4) in an oven to a temperature of 350°-500°F (177°-260°C). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.7. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 2.0012 .0003 in. (50.830 0.008 mm).9. Check the clearance between the ends of the piston rings. See PISTONS AND RINGS in SPECIFICATIONS.10. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring joint. 11. Install the oil ring on the piston with tool (B).12. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston with tool (B).13. Install the first (top) piston ring with the side that has the identification "UP-1" toward the top of the piston with tool (B). After the installation of all three piston rings, put the piston rings in position so the end gaps are 120° apart. 14. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2) and install the pin. Install retainer rings (1) with tool (A). Make sure the retainer rings are in the grooves of the piston.15. Install bearings (3) in the connecting rod and connecting rod cap.end by:a) install pistons

Have questions with 105040-2200?





Group cross 105040-2200 ZEXEL

Shinko-Engin. 

105040-2200  
9 430 615 424 
0170990830 
NOZZLE-HOLDER
Back to top