Information injector
BOSCH
0 445 110 172
0445110172
ZEXEL
107750-0210
1077500210
HONDA
16450RBDE01
16450rbde01

Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
0445110172 Diesel Injector Is Suitable Compatible For Honda(4pcs)
EGCQVSDP Select high-quality materials to prevent the corrosion of fuel, thus prolonging the service life. || Through strict simulation test, it ensures safe and stable operation under extremely high or low temperature conditions. || Check the leakage, blockage, atomization, injection angle and uniformity of each nozzle at different speeds to ensure long-term reliability. || Fuel injectors can distribute gasoline or diesel evenly, so that the engine can run with the best fuel efficiency and reduce emissions and fuel consumption. || 0445110172 Diesel Injector Is Suitable Compatible For Honda
EGCQVSDP Select high-quality materials to prevent the corrosion of fuel, thus prolonging the service life. || Through strict simulation test, it ensures safe and stable operation under extremely high or low temperature conditions. || Check the leakage, blockage, atomization, injection angle and uniformity of each nozzle at different speeds to ensure long-term reliability. || Fuel injectors can distribute gasoline or diesel evenly, so that the engine can run with the best fuel efficiency and reduce emissions and fuel consumption. || 0445110172 Diesel Injector Is Suitable Compatible For Honda
0445110172 Diesel Injector Is Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi(2pcs)
YPMOICBH It has influence on engine performance and power output. || The product is durable, good in quality and convenient to install. || The fuel nozzle sprays fuel into mist to increase the contact area between fuel and air. || Ensure that the engine can obtain the correct air-fuel ratio under different working conditions. || 0445110172 Diesel Injector Is Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi
YPMOICBH It has influence on engine performance and power output. || The product is durable, good in quality and convenient to install. || The fuel nozzle sprays fuel into mist to increase the contact area between fuel and air. || Ensure that the engine can obtain the correct air-fuel ratio under different working conditions. || 0445110172 Diesel Injector Is Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi
0445110172 Diesel Injector Is Suitable Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi(1pc)
SJJRMILX Wide range of models compatible, convenient installation, greatly saving time and effort || High efficient fuel sprays and high Impedance Coil enable fast start up in the cold environments, low fuel consumption || All applications provide precision flow rates and original spray patterns for optimal performance in all driving conditions || Made of high-quality metal, the nozzle is strong, non-aging, durable, guarantees optimum strength and durability, and has a long service life || 0445110172 Diesel Injector Is Suitable Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi
SJJRMILX Wide range of models compatible, convenient installation, greatly saving time and effort || High efficient fuel sprays and high Impedance Coil enable fast start up in the cold environments, low fuel consumption || All applications provide precision flow rates and original spray patterns for optimal performance in all driving conditions || Made of high-quality metal, the nozzle is strong, non-aging, durable, guarantees optimum strength and durability, and has a long service life || 0445110172 Diesel Injector Is Suitable Compatible For Honda Accord MK7 CR-V Civic FR-V 2.2 CDTi
Images:
USD 26.9
[23-Aug-2022]
USD 19.9
[16-May-2019]
USD 19.5
[01-Apr-2017]
USD 22
[09-May-2017]
Cross reference number
Zexel num
Bosch num
Firm num
Name
107750-0210
0 445 110 172
16450RBDE01 HONDA
INJECTOR
* C 55KE INJECTOR
* C 55KE INJECTOR
107750-0210
0 445 110 172
16450RBDAE030M5 HONDA
INJECTOR
A * C 55KE INJECTOR
A * C 55KE INJECTOR
107750-0210
0 445 110 172
16450RBDE011M5 HONDA
INJECTOR
B * C 55KE INJECTOR
B * C 55KE INJECTOR
107750-0210
0 445 110 172
0445110172 BOSCH
INJECTOR
C 55KE INJECTOR
C 55KE INJECTOR
Information:
Caterpillar does not recommend checking actual engine bearing clearances, particularly on small engines, because of the possibility of obtaining inaccurate results, and the possibility of damaging the bearing or journal surfaces. Each Caterpillar engine bearing is quality checked for specific wall thickness. If the crankshaft journals and bores for the block and rods were measured at disassembly and found to be within specifications, no further checks are necessary when using the correct bearings. However, if the serviceman still wants to measure the bearing clearances, Plastigage is an acceptable method. Plastigage is less accurate on small diameter journals where clearances are less than 0.10 mm (0.004 in.).
Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.
1. The serviceman must be very careful to use Plastigage correctly. The following points must be remembered:a. Make sure that the backs of the bearings and the bores are clean and dry.b. Make sure that the bearing locking tabs are properly seated in their slots.c. The crankshaft must be free of oil where the Plastigage touches it.d. If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.e. Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.f. Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.g. Do not turn the crankshaft with the Plastigage installed. h. Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal, See photograph.i. Remove all the Plastigage before reinstalling the cap. When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major width to make sure they are within the specification range.
Lead wire, shim stock or a dial bore gauge can damage the bearing surfaces.
1. The serviceman must be very careful to use Plastigage correctly. The following points must be remembered:a. Make sure that the backs of the bearings and the bores are clean and dry.b. Make sure that the bearing locking tabs are properly seated in their slots.c. The crankshaft must be free of oil where the Plastigage touches it.d. If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.e. Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.f. Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.g. Do not turn the crankshaft with the Plastigage installed. h. Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal, See photograph.i. Remove all the Plastigage before reinstalling the cap. When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major width to make sure they are within the specification range.
Have questions with 107750-0210?
Group cross 107750-0210 ZEXEL
Toyota
Toyota
Honda
107750-0210
0 445 110 172
16450RBDE01
INJECTOR
107750-0210
0 445 110 172
16450RBDAE030M5
INJECTOR
107750-0210
0 445 110 172
16450RBDE011M5
INJECTOR
Bosch
107750-0210
0 445 110 172
0445110172
INJECTOR