106672-2281 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1066722281 0429050980


 

Information injection-pump assembly

ZEXEL 106672-2281 1066722281
  0429050980
106672-2281 INJECTION-PUMP ASSEMBLY
Rating:
10
Buy INJECTION-PUMP ASSEMBLY 106672-2281 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106672-2281 
 
0429050980   
INJECTION-PUMP ASSEMBLY
S12A *




Information:

Operation
At all speeds the rotor blades are kept in contact with the bore of the body by centrifugal force, assisted by the hydraulic action of the oil beneath the blades. When the rotor turns, the spaces between the blades vary because of the eccentric mounting of the rotor in the exhauster body. As a blade passes the inlet port, the space between it and the following blade is increasing and air is drawn from the vacuum reservoir. This air is then compressed and expelled, with the lubricating oil, through the outlet port to the engine timing case.Periodic Inspections and Preventive Maintenance
Every 5,000 miles (7,500 km) or 250 Hours
Check the vacuum lines and fittings. (Vacuum leakage may occur through the line, or reservoir mounted non-return valve if the valve seat is dirty or pitted). Examine the exhauster for evidence of oil leakage, particularly at end cover joints, and at shaft oil seal.Check the oil supply line for leaks at fittings and connections.Check the mounting and end cover nuts and bolts for tightness.Every 60,000 Miles (90,000 km) or 2,500 Hours
Remove and dismantle exhauster, thoroughly clean all parts and inspect for wear and damage. Repair or replace the exhauster with a Factory Replacement Unit.Removal
Disconnect oil and vacuum pipes at the exhauster and plug ends to prevent the entry of foreign matter.
Q2 1. Distance Piece2. ExhausterUndo the four nuts that secure the exhauster to the timing case, and withdraw the unit complete with its driving gear, from the studs (Fig. Q.2).Dismantling
Remove the two half-round thrust plates which locate the drive gear on the front of exhauster shaft.Remove drive gear.Mark the end covers in relation to the body to correct location on re-assembly.Unscrew four setscrews and remove rear end cover with rubber sealing ring.Mark the blades in relation to the rotor.Withdraw the rotor and fibre blades from the body.Unscrew four socket headed screws, and remove drive end cover, with joint or rubber ring.Remove rear end cover circlip, blanking disc, and rubber oil seal ring, if fitted. Further dismantling of the rotor assembly need be undertaken only if, after inspection, it is found necessary to renew the bearing or shaft collar.Cleaning and Inspection Cleaning
Wash the roller bearing, where fitted, in thin flushing oil or white spirit and blow dry with compressed air. Spinning the bearing with compressed air should be avoided, otherwise damage to the rollers and race will occur.Wash the remaining components in cleaning solvent, and clear the rotor and drive end cover oilways with compressed air.Inspection of Parts
Examine the roller bearings, where fitted, for discolouration, wear, pitting and cracked races. Rotate slowly to examine for roughness. To renew, see "Overhaul" Section. Premature failure may have been caused by shortage of oil.Examine plain bearing(s) for excessive wear. To renew, see "Overhaul" Section.Inspect rotor and shaft for cracks and damage, and the shaft seal collar for wear. To renew collar, see "Overhaul" Section.Check fit of blades in rotor slots, replace any worn or damaged blades.Examine the seal(s) carefully to see that the sealing edge

Have questions with 106672-2281?





Group cross 106672-2281 ZEXEL

Mitsubishi-Heav 

 
0429050290 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A
9 400 617 062 
0429050951 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

9 400 617 063 
0429050230 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050620 

S6A

Mitsubishi-Heav 

 
0429050683 
INJECTION-PUMP ASSEMBLY
S6A
9 400 617 064 
0429050653 
INJECTION-PUMP ASSEMBLY
S6A
 
0429050621 

S6A
106672-2281  
 
0429050980 
INJECTION-PUMP ASSEMBLY
S12A
 
0429050950 
INJECTION-PUMP ASSEMBLY
S12A
Back to top