106672-2251 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1066722251 0429050683


 

Information injection-pump assembly

ZEXEL 106672-2251 1066722251
MITSUBISHI-HEAV 0429050683 0429050683
106672-2251 INJECTION-PUMP ASSEMBLY
Rating:
27
Buy INJECTION-PUMP ASSEMBLY 106672-2251 zexel genuine, new aftermarket engine parts with delivery

Service parts 106672-2251 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-5381
3. GOVERNOR 105447-5221
4. SUPPLY PUMP 105217-1331
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105663-0200
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2)
13. NOZZLE-HOLDER
14. NOZZLE
15. NOZZLE SET

Include in #1:

106672-2251 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106672-2251 
 
0429050683  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S6A * K




Information:

* For the frequency and timing of cleaning, refer to the relevant instruction manual. More frequent cleaning than necessary could damage the element or cause dust and foreign matter to be sucked into the engine.* Do not strike the element or hit it against another object to remove dust.* Do not blow compressed air against outside surfaces of the element.
Inspection Procedure Inspection: Outer Element* Shine some electric light inside the element.* Replace the element if thin spots or broken parts are evident in the filter paper, or if the packing at the top of the element is damaged. Also replace the element if the dust on the element is damp with oily smoke or soot, regardless of the replacement schedule. Inspection: Operation of dust indicator under specific negative pressure * Perform the following inspection and, if faulty, replace the dust indicator.* With no vacuum applied to the dust indicator, take measurement between the terminals 1 and 2. There should be no continuity.* Gradually apply vacuum to the dust indicator. Measure the vacuum when the continuity is made between the terminals 1 and 2.Turbocharger
Removal Sequence1 Turbocharger coupler2 Gasket3 Turbocharger insulator B4 Turbocharger insulator A5 Oil return pipe6 Gasket7 Eyebolt8 Oil pipe9 Turbocharger (See later sections.)10 Gasket*a: Exhaust manifoldX: Non-reusable parts Installation SequenceFollow the removal sequence in reverse.Tightening torque (Unit: N m {kgf m} Lubricant and/or sealant Installation Procedure Installation: Turbocharger* When installing the turbocharger, pour an appropriate amount of engine oil from the oil port so that each part operates smoothly.Turbocharger Disassembly Sequence1 Hose2 Actuator3 Coupling4 Turbine housing5 Snap ring6 Compressor cover7 O-ring8 Cartridge assemblyX: Non-resusable parts Assembly SequenceFollow the disassembly sequence in reverse.Service standards (Unit: mm) Tightening torque (Unit: N m {kgf m} Lubricant and/or sealant Work Before Removal Mating Marks* Draw a line across the coupling, turbine housing, compressor cover, and cartridge assembly. This line will serve as mating marks in the installation procedure. Removal Procedure Removal: Turbine housing
* Tap all around the end of the turbine housing with a rubber hammer or a similar tool, being careful not to damage the turbine housing.* Do not let the blades of the cartridge assembly hit the turbine housing, as they are easily bent.
Removal: Compressor Cover
* Tap all around the end of the turbine housing with a rubber hammer or a similar tool, being careful not damage the turbine housing.* Do not let the blades of the cartridge assembly hit the turbine housing, as they are easily bent.
Work after Disassembly Cleaning* Before cleaning the parts, carry out a visual inspection for any marks of burns or wear that may become difficult to find after the cleaning. If any defects are evident, replace the part(s).* Immerse the disassembled parts in an inflammable solvent (a 5 to 10 aqueous solution of Oil Clean from New Hope Co., Ltd.). Take out the parts from the solvent and dry them with compressed air. If there is any solid matter remaining on the parts, remove them with a plastic scraper or a bristle brush.
*

Have questions with 106672-2251?





Group cross 106672-2251 ZEXEL

Mitsubishi-Heav 

 
0429050290 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A
9 400 617 062 
0429050951 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

9 400 617 063 
0429050230 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050620 

S6A

Mitsubishi-Heav 

106672-2251  
 
0429050683 
INJECTION-PUMP ASSEMBLY
S6A
9 400 617 064 
0429050653 
INJECTION-PUMP ASSEMBLY
S6A
 
0429050621 

S6A
 
0429050980 
INJECTION-PUMP ASSEMBLY
S12A
 
0429050950 
INJECTION-PUMP ASSEMBLY
S12A
Back to top