106672-2220 ZEXEL 9 400 617 062 BOSCH INJECTION-PUMP ASSEMBLY 9400617062 1066722220 0429050951


 

Information injection-pump assembly

BOSCH 9 400 617 062 9400617062
ZEXEL 106672-2220 1066722220
  0429050951
106672-2220 INJECTION-PUMP ASSEMBLY
Rating:
24
Buy INJECTION-PUMP ASSEMBLY 106672-2220 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106672-2220 
106672-2221 
9 400 617 062 
0429050951   
INJECTION-PUMP ASSEMBLY
S12A * K




Information:

Installation procedure
Installation: Oil pan* Clean the sealant application surfaces of each part. * Apply a bead of sealant to each of the mating surfaces of the timing gear case, lower crankcase and front plate (at the two locations indicated the illustration). Installation: Oil pan* Clean the mating surfaces of each part. * Apply a bead of sealant to the mating surface of the oil pan evenly and without any breaks.* Mount the oil pan within three minutes of applying the sealant. Make sure that the sealant stays in place.
* Do not start the engine less than an hour after installation. If the oil pan mounting bolts were loosened or removed, be sure to reapply sealant.
Oil Pump
* Disassembly sequence1 Oil pump cover2 Driven gear3 Plug4 Relief valve spring5 Steel ball6 Gear and case7 O-ring*a Drive gear*b Oil pump gearP Locating pinX Non-reusable parts* Assembly sequenceFollow the disassembly procedure in reverse.Service standards (Unit: mm) Tightening torque (Unit: N m {kgf m}) Lubricant and/or sealant Inspection procedure
Inspection: Oil pump cover, driven gear, and gear and case* Measure the clearance between each gear's shaft and the oil pump cover, as well as between each gear's shaft and the gear and case. * If the measurements are not within the standard value range, replace the defective part(s). Inspection: Driven gear, drive gear and gear and case* Carry out the following inspection. Replace the oil pump if any defects are found. (1) Sinkage of each gear from gear and case end surface(2) Gear and case-to-tooth tip clearance for each gear Oil Cooler <Engine-Mounted Type, Engine Separately Mounted Type>, and Oil Filter <Engine-Mounted Type>
* Wipe up any spilled engine oil, as it can cause fires.* To avoid any risks of burns, take care not to touch the engine oil when the engine is hot.
* Make sure not to put any engine oil on the belt when working on the oil cooler and oil filter. Belt soiled with oil or grease may easily slip, resulting in deteriorated performance of the cooling system.* Do not reuse the oil filter elements by washing.
* Removal sequence1 Oil filter2 Plug3 Regulator valve spring4 Regulator valve5 Plug6 Bypass valve spring7 Bypass valve8 Oil cooler element9 Gasket10 Water drain plug11 Oil cooler body12 O-ring13 Gasket14 Water separate lipX Non-reusable parts* Installation sequenceFollow the removal sequence in reverse.Service standards (Unit: mm) Tightening torque (Unit: N m {kgf m}) Lubricant and/or sealant Special tools Removal procedure
Removal: Oil filter <Engine-mounted type> Inspection procedure
Inspection: Oil cooler element* Plug the outlet of the oil cooler element and connect a hose to the engine oil inlet port. Then, immerse the oil cooler element in a tank of water. * Apply an air pressure of 1.5 MPa {15 kgf/cm2} for 15 seconds through the hose, and check for any air leaks.* Replace the element if it leaks air.Installation procedure
Installation: Oil cooler <Engine-mounted type>* Clean the oil filter mounting surface of the oil cooler. * Apply a thin coat of engine oil on the oil filter gasket.* Screw in the

Have questions with 106672-2220?





Group cross 106672-2220 ZEXEL

Mitsubishi-Heav 

 
0429050290 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

 
0429050981 
INJECTION-PUMP ASSEMBLY
S12A
106672-2220  

106672-2221 
9 400 617 062 
0429050951 
INJECTION-PUMP ASSEMBLY
S12A

Mitsubishi-Heav 

9 400 617 063 
0429050230 
INJECTION-PUMP ASSEMBLY
6DE
 
0429050620 

S6A

Mitsubishi-Heav 

 
0429050683 
INJECTION-PUMP ASSEMBLY
S6A
9 400 617 064 
0429050653 
INJECTION-PUMP ASSEMBLY
S6A
 
0429050621 

S6A
 
0429050980 
INJECTION-PUMP ASSEMBLY
S12A
 
0429050950 
INJECTION-PUMP ASSEMBLY
S12A
Back to top