106662-2191 ZEXEL 9 400 616 636 BOSCH INJECTION-PUMP ASSEMBLY 9400616636 1066622191 0429050151


 

Information injection-pump assembly

BOSCH 9 400 616 636 9400616636
ZEXEL 106662-2191 1066622191
MITSUBISHI-HEAV 0429050151 0429050151
106662-2191 INJECTION-PUMP ASSEMBLY
Rating:
17
Buy INJECTION-PUMP ASSEMBLY 106662-2191 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106662-2191 
9 400 616 636 
0429050151  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
6DH K 14CA INJECTION PUMP ASSY PE6P,6PD PE




Information:

Use Again - if wear on contact surfaces cannot be felt with a seal pick.
Illustration 46 g06346577
Rack control and limiting sleeve.
Use Again - if wear on contact surfaces cannot be felt with a seal pick.Riser Shaft and Pin
Illustration 47 g06346580
Riser shaft.
Use Again - if there is no wear step on the shaft, which can be felt with a seal pick. If a step is present, it will generally occur near the center of the shaft.
Illustration 48 g06346583
Normal wear on pin at end of riser shaft.
Use Again
Illustration 49 g06346588
Pin with material eroded away near the center relief.
Do Not Use AgainFlyweight and Dowel
Illustration 50 g06346593
Flyweight toe with gouges near dowel hole.
Do Not Use Again - if wear marks can be felt with a seal pick.
Illustration 51 g06346599
Flyweight toe wear.
Do Not Use Again
Illustration 52 g06346602
Flyweight toe wear.
Do Not Use Again - if there are any signs of "flat spots". Worn flyweight toes may be highly polished so that flat spots are difficult to feel. Hold the flyweight toe surface in bright light and watch for changes in reflection in worn areas. Use a new flyweight toe for comparison.
Illustration 53 g06346609
Acceptable wear on flyweight dowel.
Use Again - if wear cannot be felt with a seal pick.
Illustration 54 g06346611
Heavy wear on flyweight dowel.
Do Not Use AgainNote: Examine the dowel seating area on the flyweight carrier. If there is any apparent wear, reinstall dowels in the unused positions, 90 degrees from original position.Bearing Assembly
Illustration 55 g06346614
The bearing (white collar) shown in position on the FARC diaphragm retainer (Type V, VI, and VII Governors) shows wear.
Do Not Use AgainGovernor Spring Seat
Illustration 56 g06346615
Governor spring seat with typical wear.
Use Again - if there are no gouges to surfaces (1) on the spring seating area.Spring Pack
Illustration 57 g06346618
End view of governor spring pack.
Use Again - after realignment.Note the off-center position of the internal springs with respect to the outside spring. This can cause governor instability, which results in surging. Rotate the springs on their seat so that the inner springs are aligned (centered) with respect to the outer spring. Remove sharp edges (A) from the inside diameter of the flat surface on the springs to ensure springs seat properly.

Have questions with 106662-2191?





Group cross 106662-2191 ZEXEL

Mitsubishi-Heav 

 
0429050170 

6DH
 
0429050551 
INJECTION-PUMP ASSEMBLY
12DH
 
0429050552 
INJECTION-PUMP ASSEMBLY
12DH
9 400 616 634 
0429050582 
INJECTION-PUMP ASSEMBLY
12DH
 
0429050522 
INJECTION-PUMP ASSEMBLY
12DH
 
0429050502 

12DH
9 400 616 635 
0429050181 
INJECTION-PUMP ASSEMBLY
6DH
106662-2191  
9 400 616 636 
0429050151 
INJECTION-PUMP ASSEMBLY
6DH
Back to top