103864-0110 ZEXEL 9 400 616 399 BOSCH INJECTION-PUMP ASSEMBLY 9400616399 1038640110 0429104600


 

Information injection-pump assembly

BOSCH 9 400 616 399 9400616399
ZEXEL 103864-0110 1038640110
MITSUBISHI-HEAV 0429104600 0429104600
103864-0110 INJECTION-PUMP ASSEMBLY
Rating:
21
Buy INJECTION-PUMP ASSEMBLY 103864-0110 zexel genuine, new aftermarket engine parts with delivery

Service parts 103864-0110 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 103086-0121
3. GOVERNOR
4. SUPPLY PUMP 105235-1581
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105663-0150
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105113-3020
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 34.3{350}
13. NOZZLE-HOLDER
14. NOZZLE 105011-1790
15. NOZZLE SET

Include in #1:

103864-0110 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
103864-0110 
103864-0150 
9 400 616 399 
0429104600  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S16N K 14BS INJECTION PUMP ASSY PE4-8Z PE




Information:

Outside Leaks
Leaks in Hoses or Connections ... Check all hoses and connections for visual signs of leakage. If no leaks are seen, look for damage to hoses or loose clamps.Leaks in the Radiator and/or Expansion Tank ... Put pressure to the radiator and/or expansion tank with a cooling system pressurizing pump and check for leaks.Leaks in the Heater ... Put pressure to the cooling system with a cooling system pressurizing pump and check the heater for leaks.Leaks in the Water Pump ... Check the water pump for leaks before starting the engine, then start the engine and look for leaks. If there are leaks at the water pump, install a new water pump.Cylinder Head Gasket Leakage ... Look for leaks along the surface of the cylinder head gasket. If you see leaks, install a new head gasket.Coolant Leaks At The Overflow Tube
Defective Pressure Cap ... Check the sealing surfaces of the pressure cap and the radiator to be sure the cap is sealing correctly. Check the opening pressure and sealing ability of the pressure cap with a cooling system pressurizing pump.Engine Runs Too Hot ... If coolant temperature is too high, pressure will be high enough to lift the cap off of the sealing surface in the radiator and cause coolant loss through the overflow tube. See "Above Normal Heating" in COOLING SYSTEM chart.Expansion Tank Too Small or Installed Wrong ... The expansion tank can be either a part of the radiator or it can be installed separately from the radiator. The expansion tank must be large enough to hold the expansion of the coolant as it gets warm or has sudden changes in pressure. Make sure the expansion tank is installed correctly and is according to the recommendations of the truck manufacturer.Cylinder Head Gasket Leakage, or Crack(s) in Cylinder Head or Cylinder Block ... Remove the radiator cap and with the engine running look for air bubbles in the coolant. Bubbles in the coolant are a sign of probable leakage at the head gasket. With the engine not running, check each cylinder with the cylinder leakage tester. If you see air bubbles in the coolant during this test, there is a leak of combustion gas into the cooling system. Remove the cylinder heads from the engine. Check cylinder heads, cylinder walls and head gasket surface of cylinder block for cracks. When installing heads, use new head gaskets. *Inside Leakage
Cylinder Head Gasket Leakage ... If the cylinder head gasket leaks between a water passage and an opening into the crankcase, coolant will get into the crankcase.Crack(s) in Cylinder Head ... Crack(s) in the upper surface of the cylinder head or an area between a water passage and an opening into the crankcase can allow coolant to get into the crankcase.Crack(s) in Cylinder Block ... Crack(s) in the cylinder block between a water passage and the crankcase will let coolant get into the crankcase.*Authorized dealers are equipped with the necessary tools and personnel familiar with disassembly and assembly procedures

Have questions with 103864-0110?





Group cross 103864-0110 ZEXEL

 
0429104500 
INJECTION-PUMP ASSEMBLY
S16N

Mitsubishi-Heav 

103864-0110  

103864-0150 
9 400 616 399 
0429104600 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104490 
INJECTION-PUMP ASSEMBLY
S16N

Mitsubishi-Heav 

 
0429104700 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104790 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104800 
INJECTION-PUMP ASSEMBLY
S16N
 
3746502001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746522000 
INJECTION-PUMP ASSEMBLY
S16N
9 400 610 382 
3746522001 
INJECTION-PUMP ASSEMBLY
S16N
9 400 610 382 
3746532000 
INJECTION-PUMP ASSEMBLY
S16N
 
3746501001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746521000 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 400 
3746521001 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 400 
3746531000 
INJECTION-PUMP ASSEMBLY
S16N
 
3746511001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746521100 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 401 
3746521101 
INJECTION-PUMP ASSEMBLY
S16N
 
3746512001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746522100 
INJECTION-PUMP ASSEMBLY
S8N
Back to top