103864-0100 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1038640100 0429104500


 

Information injection-pump assembly

ZEXEL 103864-0100 1038640100
  0429104500
103864-0100 INJECTION-PUMP ASSEMBLY
Rating:
20
Buy INJECTION-PUMP ASSEMBLY 103864-0100 zexel genuine, new aftermarket engine parts with delivery

Service parts 103864-0100 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 103086-0060
3. GOVERNOR
4. SUPPLY PUMP 105235-1351
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2)
13. NOZZLE-HOLDER
14. NOZZLE
15. NOZZLE SET

Include in #1:

103864-0100 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
103864-0100 
103864-0110 
 
0429104500   
INJECTION-PUMP ASSEMBLY
S16N *




Information:

Above Normal Heating
Low Coolant Level ... If the coolant level is too low, not enough coolant will go through the engine and radiator. This lack of coolant will not take enough heat from the engine and there will not be enough coolant flow through the radiator to release the heat into the cooling air. Low coolant level is caused by leaks or wrong filling of the radiator. With the engine cool, be sure that coolant can be seen at the low end of the fill neck or at the sight glass on the radiator top tank.Defective Temperature Gauge ... A temperature gauge which does not work correctly will not show the correct temperature. If the temperature gauge shows that the coolant temperature is to hot but other conditions are normal, install a thermometer you know is correct and/or check the cooling system.Dirty Radiator ... Check the radiator core for debris which prevents free air flow. Check the radiator for debris, dirt, or deposits on the inside of the radiator core which prevents free flow of coolant through the radiator.Loose Belts ... Loose fan or water pump belts will cause a reduction in air or water flow. Tighten belts until a 25 lb. (11,3 kg) force at the half way point between the pulleys, moves the belts .875 .125 in. (22,0 3,0 mm).Defective Hoses ... Leaks in hoses can normally be seen. Hoses that have no visual leaks can collapse during operation and cause restriction in the flow of coolant. Hoses become soft and/or get cracks after a period of time. Change hoses after a year of use. The inside can become loose and the loose particles can cause a restriction in the flow of coolant.Shunt Line Restriction ... A restriction of the shunt line from the radiator top tank to the engine front cover, or a shunt line not installed correctly, will cause a reduction in water pump efficiency. The result will be low coolant flow and over-heating.Shutters Not Opening Correctly ... Check the opening temperature of the shutters. The shutters must be open at 200°F (93°C).Defective Thermostats ... A thermostat that does not open or only opens part of the way can cause above normal heating. To test the thermostats, see the topic WATER TEMPERATURE THERMOSTAT.Defective Water Pump* ... A water pump with a loose pulley or impeller does not pump enough coolant for correct engine cooling. A loose pulley or impeller can be found by removing the drive belt for the water pump and by pushing the pulley back and pulling it forward.Air in Cooling System ... Air can get into the cooling system in different ways. The most common causes are not filling the cooling system correctly, and combustion gas leaking into the system. Combustion gas can get into the system through inside cracks or bad cylinder head gaskets. Air in the cooling system causes a reduction in coolant flow and bubbles in the coolant. Air bubbles hold coolant away from engine parts,

Have questions with 103864-0100?





Group cross 103864-0100 ZEXEL

103864-0100  

103864-0110 
 
0429104500 
INJECTION-PUMP ASSEMBLY
S16N

Mitsubishi-Heav 

9 400 616 399 
0429104600 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104490 
INJECTION-PUMP ASSEMBLY
S16N

Mitsubishi-Heav 

 
0429104700 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104790 
INJECTION-PUMP ASSEMBLY
S16N
 
0429104800 
INJECTION-PUMP ASSEMBLY
S16N
 
3746502001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746522000 
INJECTION-PUMP ASSEMBLY
S16N
9 400 610 382 
3746522001 
INJECTION-PUMP ASSEMBLY
S16N
9 400 610 382 
3746532000 
INJECTION-PUMP ASSEMBLY
S16N
 
3746501001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746521000 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 400 
3746521001 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 400 
3746531000 
INJECTION-PUMP ASSEMBLY
S16N
 
3746511001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746521100 
INJECTION-PUMP ASSEMBLY
S16N
9 400 616 401 
3746521101 
INJECTION-PUMP ASSEMBLY
S16N
 
3746512001 
INJECTION-PUMP ASSEMBLY
S16N
 
3746522100 
INJECTION-PUMP ASSEMBLY
S8N
Back to top