103664-1140 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1036641140 0429103800


 

Information injection-pump assembly

ZEXEL 103664-1140 1036641140
MITSUBISHI-HEAV 0429103800 0429103800
103664-1140 INJECTION-PUMP ASSEMBLY
Rating:
16
Buy INJECTION-PUMP ASSEMBLY 103664-1140 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
103664-1140 
 
0429103800  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S12N * K




Information:

(1) Remove the plug in the dash and install 3T306 Starting Aid Switch (1). Connect two purple wires (2), from the wiring harness, to switch (1).(2) On machines with a bulldozer, remove two nuts (3), washers and bolts. Remove two bolts (4) and washers. Remove bracket (5) from bracket (6). (3) Put 7G6359 Box Assembly (7) in position and install two 5F4899 Bolts (8) and 5M2894 Washers. Install two S1594 Bolts (9), 5P1075 Washers and 1D4717 Nuts to hold box assembly (7) to bracket (6). Install 4M7470 Grommet in hole (A).(4) Put the wires of 6N7674 Valve Assembly (10) through hole (A) and install valve assembly (10) on box assembly (7) with two S1617 Bolts (11), 5P4116 Washers and 1D4716 Nuts. Install 7N2059 Clamp Assembly (12) with two S1617 Bolts, 5P4116 Washers and 1D4716 Nuts. Install 63801 Washer (13) on 6D1746 Bolt (14). Put bolt (14) in position in cover (15) and install L1365 Washer (16) on bolt (14). Install 3B4610 Cotter Pin (17) in bolt (14). (5) Remove the plug from the manifold and install 6N9995 Atomizer Assembly (18) as shown. The orifices of the atomizer must be toward each end of the manifold. Install 5P7907 Connector (19) in valve assembly (10). Connect 9G941 Tube (20) to atomizer assembly (18). Use 5P6314 Sleeve (21) and 5P6313 Nut (22) to connect tube (20) to connector (19). Remove the plug from the bypass elbow of the water lines group and install 6N5899 Switch (23). Connect 9G6560 Wire Assembly (24) to switch (23) and to valve assembly (10). Connect 9G6561 Wire Assembly (25) to valve assembly (10) and to the purple wire, from the starting aid switch, at the rear of the engine. Use former clips (26) to hold wire assemblies (24) and (25) in position.(6) Remove cap (27) from valve assembly (10) and install a 7N296 Cylinder Assembly. (7) For machines without bulldozer lines, remove the two bolts from the cylinder head and put 7G6359 Box Assembly (7) in position. Install two 5F4899 Bolts (8) and 5M2894 Washers. Remove the bolt from the exhaust manifold and put 3T1685 Bracket (27) in position. Install L2070 Bolt (28), 5M2894 Washer and 1D4717 Nut. Install two S1594 Bolts (9), 5P1075 Washers and 1D4717 Nuts. Install the 4M7470 Grommet in hole (A), see Step 3. Follow Steps 1, 4, 5 and 6 for installation of the group.

Have questions with 103664-1140?





Group cross 103664-1140 ZEXEL

 
0429103400 
INJECTION-PUMP ASSEMBLY
S12N

Mitsubishi-Heav 

 
0429103490 
INJECTION-PUMP ASSEMBLY
S12N
 
0429105200 
INJECTION-PUMP ASSEMBLY
S6N
 
0429103700 
INJECTION-PUMP ASSEMBLY
S12N
 
0429103790 
INJECTION-PUMP ASSEMBLY
S12N
 
0429103600 
INJECTION-PUMP ASSEMBLY
S12N
103664-1140  
 
0429103800 
INJECTION-PUMP ASSEMBLY
S12N
 
3716502001 
INJECTION-PUMP ASSEMBLY
S6N
9 400 612 217 
3716522000 
INJECTION-PUMP ASSEMBLY
S6N
 
3736501001 
INJECTION-PUMP ASSEMBLY
S12N
9 400 616 313 
3736521000 
INJECTION-PUMP ASSEMBLY
S12N
 
3736511001 
INJECTION-PUMP ASSEMBLY
S12N
9 400 611 790 
3736521100 
INJECTION-PUMP ASSEMBLY
S12N
 
3716505000 
INJECTION-PUMP ASSEMBLY
S6N
 
3716512001 
INJECTION-PUMP ASSEMBLY
S6N
Back to top