101491-1250 ZEXEL 9 400 614 314 BOSCH INJECTION-PUMP ASSEMBLY 9400614314 1014911250 me080229

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 614 314 9400614314

ZEXEL 101491-1250 1014911250

MITSUBISHI ME080229 me080229

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101491-1250 zexel genuine, new aftermarket engine parts with delivery

Service parts 101491-1250 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101049-9031

3. GOVERNOR 105402-2180

4. SUPPLY PUMP 105220-5180

5. AUTOM. ADVANCE MECHANIS 105676-0260

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6(220)

13. NOZZLE-HOLDER 105048-3010

14. NOZZLE

105017-0100

15. NOZZLE SET

Include in #1:

101491-1250 as INJECTION-PUMP ASSEMBLY

101602-3981 as _

Cross reference number

BOSCH 9 400 614 314 9400614314

ZEXEL 101491-1250 1014911250

MITSUBISHI ME080229 me080229

Zexel num

Bosch num

Firm num

Name

101491-1250

9 400 614 314

ME080229 MITSUBISHI

INJECTION-PUMP ASSEMBLY
4D31T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 10

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 52.4 51.4 53.4

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8.2+-0.5

Pump speed r/min 375 375 375

Average injection quantity mm3/st. 7.5 6.2 8.8

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point C

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 64 64 69

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min 1100

Advance angle deg. 1.2 0.9 1.5

Timer adjustment_03

Pump speed r/min 1500

Advance angle deg. 3 3 3

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Supplied with torque spring not set. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)At shipping (7)Rack difference between N = N1 and N = N2
----------
K=14 N1=1500r/min N2=400r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)At shipping (2)Stopper bolt setting
----------

----------
a=(24deg)+-5deg b=(18deg)+-5deg c=(2deg)

Stop lever angle

N:Pump normal S:Stop the pump. (1)At shipping
----------

----------
a=38deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(130deg)

Information:

This Program can only be administeredafter a failure occurs. The decision whether to apply the Program is madeby the dealer. When reporting the repair, use "PS50780" as the Part numberand "7755" as the Group Number. Use "96" as the Warranty Claim DescriptionCode and use "Z" as the SIMS Description Code. The information supplied in this serviceletter may not be valid after the termination date of this program. Donot perform the work outlined in this Service Letter after the terminationdate without first contacting your Caterpillar product analyst. This Revised Service Letter replacesthe April 2, 2004 (Revised April 2004) Service Letter. Changes have beenmade to the Affected Product.TERMINATION DATE
April 30, 2006PROBLEM
Failed injector and wiring harness need to bereplaced on certain C-9 Industrial Engines. The C-9 engine can developan injector misfire due to an open connection at the injector to harnessconnector. This misfire can be diagnosed with standard troubleshootingguide procedures.AFFECTED PRODUCT
Model Identification Number
C9 CLJ1-4259
12H 12500001-40AMZ1-496CBK1-353
330C B1K1-178B2L1-203B4N1-187BTM1-189CGZ1-511CYA1-287D3C1-231JAB1-626JCD1-292JNK1-245KDD1-580MCA1-427MKM1-308GAG1-329RBH1-233
330C L CAP1-1257DKY1-2011HAA1-393
D6R II AEM1-100AFM1-115BLE1-199BLT1-186BMK1-121BNL1-99BPM1-101BPP1-97BPS1-102BRJ1-116
D6R II LGP ACJ1-101ADE1-311BNC1-265BPZ1-142
D6R II XL AAX1-465BMJ1-130BMY1-297BRZ1-115CAD1-143FDT1-141
D6R II XW AEP1-223DAE1-129
470 7651-811
475 7671-824
MT765 AMS1-266
TK711 10100001-00191
TK721 10200001-00191
TK722 10300001-00193
TK732 10400185-00190
627G CEX187-296
637G CEH222-255PARTS NEEDED
Qty
Part Number
Description
1 1567106 Wiring Kit
1 1889865 Harness Assembly
1 2359651 Bolt - Socket
1 2360962 Injector GroupACTION REQUIRED
Replace the single failed injector with the new 2360962 Injector and the1889865 Wiring Harness Assembly. Refer to REHS1809 Special Instructionfor use of the 1567106 Wiring Kit.SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts Labor Hrs Parts Labor Hrs Parts Labor Hrs
0-5000
0-35 months 100% 2.0 0 0 0 0
This is a 2?hour job.PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warrantyparts handling.