Buy 101431-4050 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1014314050 8944574250


 

Information injection-pump assembly

ZEXEL 101431-4050 1014314050
ISUZU 8944574250 8944574250
101431-4050 INJECTION-PUMP ASSEMBLY
Rating:
34
Buy INJECTION-PUMP ASSEMBLY 101431-4050 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$1,210.00

20 Aug 2024

US: Gowe
GOWE Engine genset C240 Injection Pump 101431-4050 168P0686
GOWE C240 engine parts :C240 fuel injection pump ; Application:Forklift

You can express buy:

USD 550
23-10-2018
For I-suzu engine genset C240 injection pump 101431-4050 168P0686

Service parts 101431-4050 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101043-9310
3. GOVERNOR 105410-5770
4. SUPPLY PUMP 105220-4742
5. AUTOM. ADVANCE MECHANIS 105621-0370
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105151-1451
11. Nozzle and Holder 5-15300-039-1
12. Open Pre:MPa(Kqf/cm2) 11.8{120}
13. NOZZLE-HOLDER 105081-3141
14. NOZZLE 105000-1650
15. NOZZLE SET

Include in #1:

101431-4050 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
101431-4050 
 
8944574250  ISUZU
INJECTION-PUMP ASSEMBLY
C240 * K 14BC PE4A,5A, PE




Information:

1. Disconnect water supply hose from water pump inlet.2. Remove connector pipe (1), remove two bolts (2) and remove oil fill pipe (3). 3. Remove bolts (4) and (5) then remove the water pump. The following steps are for the installation of the water pump.4. Position the water pump and install two bolts (5) and (6). Tighten the two bolts evenly.5. Position connector pipe (1) and gaskets then install the bolts.6. Install oil fill pipe (3). Be sure the gasket is in position between the regulator and pipe and install bolts (2).End By:a. Install alternator (if removed)b. Fill the cooling system to the specified level. See the Maintenance Manual.Disassemble And Assemble Water Pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in.).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump

Have questions with 101431-4050?





Group cross 101431-4050 ZEXEL

Isuzu 

 
8944223520 
INJECTION-PUMP ASSEMBLY
C240
 
8944286451 
INJECTION-PUMP ASSEMBLY
C240
9 400 612 064 
8944457490 
INJECTION-PUMP ASSEMBLY
C240
9 400 614 094 
8944286453 
INJECTION-PUMP ASSEMBLY
C240
 
8944602830 
INJECTION-PUMP ASSEMBLY
C240
101431-4050  
 
8944574250 
INJECTION-PUMP ASSEMBLY
C240
9 400 614 095 
8944612510 
INJECTION-PUMP ASSEMBLY
C240
9 400 619 644 
8944681300 
INJECTION-PUMP ASSEMBLY
C240
9 400 612 563 
8944681302 
INJECTION-PUMP ASSEMBLY
C240
9 400 614 096 
8944781250 
INJECTION-PUMP ASSEMBLY
C240
9 400 614 097 
8943110160 
INJECTION-PUMP ASSEMBLY
C240
Back to top