159560-0900 ZEXEL 9 421 613 598 BOSCH GOVERNOR HOUSING 9421613598 1595600900 1157212820


 

Information governor housing

BOSCH 9 421 613 598 9421613598
ZEXEL 159560-0900 1595600900
ISUZU 1157212820 1157212820
159560-0900 GOVERNOR HOUSING
Rating:
15
Buy GOVERNOR HOUSING 159560-0900 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
159560-0900 
9 421 613 598 
1157212820  ISUZU
GOVERNOR HOUSING
C 14GH HOUSING;GOV. GOV
159560-0900 
9 421 613 598 
ME731054  MITSUBISHI
GOVERNOR HOUSING
C 14GH HOUSING;GOV. GOV
159560-0900 
9 421 613 598 
1935699218  NISSAN-DIESEL
GOVERNOR HOUSING
C 14GH HOUSING;GOV. GOV




Information:

Do not put oil on the bearings until the bearing clearance has been checked.1. Install bearings (1) in the connecting rods they were removed from. Make sure the tab in each bearing is in alignment with the notch in each connecting rod.2. Install bearings (2) in the cylinder block. Make sure the tab in each bearing is in alignment with the notch in the cylinder block. 3. Install pin (3) in the end of the crankshaft. Install the pin so that it extends a maximum of 6.4 mm (.252 in) above the surface. 4. Install the dowel in the crankshaft that puts gear (4) in the correct position. Install the dowel so that it extends 4.1 0.5 mm (.161 .020 in) above the surface of the crankshaft.5. Heat gear (4) to a maximum temperature of 233° C (451° F). Gear (4) must be installed on the crankshaft with the "V" timing mark toward the outside.6. Install gear (4) on the crankshaft. Make sure the notch in the gear is in alignment with the dowel on the crankshaft. The dimension from the rear face of the gear to the front face of the crankshaft must be 45.54 0.25 mm (1.793 .010 in). 7. Fasten Tooling (A) and a hoist to the crankshaft (5) as shown. Install the crankshaft in the engine. The weight of the crankshaft is approximately 131 kg (290 lb). 8. Make sure that "V" mark (6) on the crankshaft is in alignment with "V" mark (7) on the idler gear. The side of each thrust plate (8) with the words "BLOCK SIDE" must be installed with this side toward the cylinder block.9. Put clean oil on thrust plates (8). Install thrust plates (8) next to the center main bearings. Do not put oil on bearings (9) until the bearing clearances have been checked.10. Put bearings (9) in their original position in crankshaft main bearing caps (10).11. Check the crankshaft main bearing clearance with Plastigage as follows:a. Put a piece of Plastigage between the crankshaft bearing journal surface and bearing (9).b. Install the crankshaft main bearing caps (10) with the arrow on each cap toward the front of cylinder block. Each crankshaft main bearing cap has a number on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put 2P-2506 Thread Lubricant on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end of the cap

Have questions with 159560-0900?





Group cross 159560-0900 ZEXEL

Isuzu 

159560-0900  
9 421 613 598 
1157212820 
GOVERNOR HOUSING

Mitsubishi 

159560-0900  
9 421 613 598 
ME731054 
GOVERNOR HOUSING

Nissan-Diesel 

159560-0900  
9 421 613 598 
1935699218 
GOVERNOR HOUSING
Back to top