Information fuel-injection pump
BOSCH
9 410 618 113
9410618113
ZEXEL
104207-3002
1042073002
ISEKI
62156000882F
62156000882f

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104207-3002 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | 105148-1132 |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | 11.8{120} |
10. | NOZZLE-HOLDER | 105078-0062 |
11. | NOZZLE | 105007-1140 |
Scheme ###:
5. | [3] | 140153-9620 | PLUNGER-AND-BARREL ASSY |
12. | [3] | 140110-3620 | DELIVERY-VALVE ASSEMBLY |
13. | [3] | 140112-3300 | COMPRESSION SPRING |
16. | [3] | 140115-2200 | GASKET D12.8&8.6T0.5 |
17. | [3] | 140116-7220 | FITTING |
20. | [3] | 140118-0500 | O-RING |
30. | [3] | 140131-0021 | FLANGE BUSHING |
31. | [3] | 140271-0000 | BEARING PIN |
32. | [6] | 140118-0400 | O-RING |
37. | [6] | 140124-0100 | FLAT-HEAD SCREW |
40. | [3] | 140200-2320 | TAPPET |
44. | [3] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-0900 | LOCKING WASHER |
50. | [3] | 140215-2000 | COMPRESSION SPRING |
51. | [3] | 140216-1300 | SLOTTED WASHER |
52. | [3] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-7220 | CONTROL ROD |
65. | [1] | 140262-1421 | PLATE |
66. | [4] | 140252-0001 | FLAT-HEAD SCREW |
77. | [3] | 140241-4021 | CONTROL SLEEVE |
93. | [1] | 140402-2620 | EYE BOLT |
110. | [1] | 140420-2400 | BLEEDER SCREW |
111. | [1] | 026506-1040 | GASKET D9.9&6.2T1 |
170. | [1] | 140405-0100 | CAPSULE |
171. | [1] | 026510-1340 | GASKET D13.4&10.2T1 |
900. | [3] | 140191-0921 | PLUNGER-AND-BARREL ASSY |
900/5. | [1] | 140153-9620 | PLUNGER-AND-BARREL ASSY |
900/12. | [1] | 140110-3620 | DELIVERY-VALVE ASSEMBLY |
900/13. | [1] | 140112-3300 | COMPRESSION SPRING |
900/16. | [1] | 140115-2200 | GASKET D12.8&8.6T0.5 |
900/17. | [1] | 140116-7220 | FITTING |
900/20. | [1] | 140118-0500 | O-RING |
900/30. | [1] | 140131-0021 | FLANGE BUSHING |
900/31. | [1] | 140271-0000 | BEARING PIN |
900/32. | [2] | 140118-0400 | O-RING |
Cross reference number
Zexel num
Bosch num
Firm num
Name
104207-3002
62156000882F ISEKI
FUEL-INJECTION PUMP
K 23MC FUEL INJECTION PUMP PFR-3MD PFR
K 23MC FUEL INJECTION PUMP PFR-3MD PFR
Information:
1. Remove cylinder head bolts (1) and (2).
When lifting cylinder head, care must be taken to keep cylinder head level to prevent damage to the two cylinder head-to-spacer block dowels.
2. Lift the cylinder head off the spacer block. The approximate weight of the cylinder head is 236 kg (520 lb). The following steps are for the installation of the cylinder head.3. Thoroughly clean cylinder head and spacer block surfaces.4. Position the head gasket and the cylinder head onto the dowels in the spacer block. Lower the cylinder head onto the spacer block.5. Put engine oil on the threads of bolts (1) and (2), then install bolts. Tighten bolts (1) and (2) as follows:
Cylinder Head Tightening Sequencea. Tighten bolts 1 thru 26 in number sequence shown to a torque of 150 15 N m (110 11 lb ft).b. Tighten bolts 1 thru 26 in number sequence shown to a torque of 275 15 N m (200 11 lb ft).c. Retorque bolts 1 thru 26 in number sequence shown to 275 15 N m (200 11 lb ft).d. Tighten bolts 27 thru 33 in number sequence show to a torque of 25 7 N m (18 5 lb ft).End By:a. install valve cover baseb. install (EUI) fuel injectorsc. install rocker arm assemblies and push rodsd. adjust all the valve rocker arm clearances.e. install water outlet manifoldf. install exhaust manifold
When lifting cylinder head, care must be taken to keep cylinder head level to prevent damage to the two cylinder head-to-spacer block dowels.
2. Lift the cylinder head off the spacer block. The approximate weight of the cylinder head is 236 kg (520 lb). The following steps are for the installation of the cylinder head.3. Thoroughly clean cylinder head and spacer block surfaces.4. Position the head gasket and the cylinder head onto the dowels in the spacer block. Lower the cylinder head onto the spacer block.5. Put engine oil on the threads of bolts (1) and (2), then install bolts. Tighten bolts (1) and (2) as follows:
Cylinder Head Tightening Sequencea. Tighten bolts 1 thru 26 in number sequence shown to a torque of 150 15 N m (110 11 lb ft).b. Tighten bolts 1 thru 26 in number sequence shown to a torque of 275 15 N m (200 11 lb ft).c. Retorque bolts 1 thru 26 in number sequence shown to 275 15 N m (200 11 lb ft).d. Tighten bolts 27 thru 33 in number sequence show to a torque of 25 7 N m (18 5 lb ft).End By:a. install valve cover baseb. install (EUI) fuel injectorsc. install rocker arm assemblies and push rodsd. adjust all the valve rocker arm clearances.e. install water outlet manifoldf. install exhaust manifold