Information fuel-injection pump
BOSCH
9 410 617 205
9410617205
ZEXEL
104207-2000
1042072000
ISEKI
62156000570
62156000570

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104207-2000 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | 105148-1132 |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | 11.8{120} |
10. | NOZZLE-HOLDER | 105078-0062 |
11. | NOZZLE | 105007-1140 |
Scheme ###:
5. | [2] | 140153-9620 | PLUNGER-AND-BARREL ASSY |
12. | [2] | 140110-3620 | DELIVERY-VALVE ASSEMBLY |
13. | [2] | 140112-3300 | COMPRESSION SPRING |
16. | [2] | 140115-2200 | GASKET D12.8&8.6T0.5 |
17. | [2] | 140116-7220 | FITTING |
20. | [2] | 016550-1220 | O-RING |
30. | [2] | 140131-0021 | FLANGE BUSHING |
31. | [2] | 140271-0000 | BEARING PIN |
32. | [4] | 016550-1620 | O-RING |
37. | [4] | 140124-0100 | FLAT-HEAD SCREW |
40. | [2] | 140200-2320 | TAPPET |
44. | [2] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-0800 | LOCKING WASHER |
50. | [2] | 140215-2000 | COMPRESSION SPRING |
51. | [2] | 140216-1300 | SLOTTED WASHER |
52. | [2] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-3221 | CONTROL ROD |
65. | [1] | 140262-0400 | PLATE |
66. | [4] | 140252-0000 | FLAT-HEAD SCREW |
77. | [2] | 140241-4021 | CONTROL SLEEVE |
93. | [1] | 140402-2620 | EYE BOLT |
110. | [1] | 140420-2400 | BLEEDER SCREW |
111. | [1] | 026506-1040 | GASKET D9.9&6.2T1 |
Cross reference number
Zexel num
Bosch num
Firm num
Name
62156000570 ISEKI
FUEL-INJECTION PUMP
* K 23MB FUEL INJECTION PUMP PFR-2MD PFR
* K 23MB FUEL INJECTION PUMP PFR-2MD PFR
Information:
1. Remove bolts (1) and (2) from engine oil pump manifold (3). 2. Remove four bolts (4) and remove oil pump. The following steps are for the installation of the engine oil pump.3. With O-ring seal in place, on oil pump flange, position the oil pump and install four bolts (4). Tighten bolts (4) evenly to pull oil pump into place.4. Position gaskets and install bolts (1) and (2) to hold manifold.End By:a. install oil filterDisassemble & Assemble Engine Oil Pump
Start By:a. remove oil pump 1. Remove manifold (1). Remove four bolts (2) and remove cover (3). 2. Remove O-ring seal (4) and gear (5).3. Use Tooling (A) and remove driver gear (6).
Before removing input shaft and gear (7) from pump housing, be sure no burrs exist on the input shaft. If the shaft has burrs it could scratch the pump housing and damage it.
4. Remove input shaft and gear (7) from pump housing. The following steps are for the assembly of the engine oil pump.5. Position input shaft and gear (7) in pump housing. Press drive gear (6) onto input shaft until it is flush with the end of the shaft.6. Install gear (6). Install O-ring (4) in cover (3), then install cover and bolts (2). 7. With O-rings in place, install manifold (1).End By:a. install engine oil pump
Start By:a. remove oil pump 1. Remove manifold (1). Remove four bolts (2) and remove cover (3). 2. Remove O-ring seal (4) and gear (5).3. Use Tooling (A) and remove driver gear (6).
Before removing input shaft and gear (7) from pump housing, be sure no burrs exist on the input shaft. If the shaft has burrs it could scratch the pump housing and damage it.
4. Remove input shaft and gear (7) from pump housing. The following steps are for the assembly of the engine oil pump.5. Position input shaft and gear (7) in pump housing. Press drive gear (6) onto input shaft until it is flush with the end of the shaft.6. Install gear (6). Install O-ring (4) in cover (3), then install cover and bolts (2). 7. With O-rings in place, install manifold (1).End By:a. install engine oil pump