104207-1021 ZEXEL 9 410 618 416 BOSCH FUEL-INJECTION PUMP 9410618416 1042071021 2566310300


 

Information fuel-injection pump

BOSCH 9 410 618 416 9410618416
ZEXEL 104207-1021 1042071021
FUJI-HEAVY 2566310300 2566310300
104207-1021 FUEL-INJECTION PUMP
Rating:
26
Buy FUEL-INJECTION PUMP 104207-1021 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104207-1021
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

5. [1] 140154-0420 PLUNGER-AND-BARREL ASSY M15
12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY K25
13. [1] 140112-2800 COMPRESSION SPRING
16. [1] 140115-2200 GASKET
17. [1] 140116-7220 FITTING
20. [1] 140118-0500 O-RING
30. [1] 140131-0021 FLANGE BUSHING
31. [1] 140271-0000 BEARING PIN
32. [2] 140118-0400 O-RING
37. [2] 140124-0100 FLAT-HEAD SCREW
40. [1] 140200-2320 TAPPET
44. [1] 140212-0500 BEARING PIN
45. [1] 140213-1300 LOCKING WASHER
50. [1] 140215-2000 COMPRESSION SPRING
51. [1] 140216-1300 SLOTTED WASHER
52. [1] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-3422 CONTROL ROD
65. [1] 140262-0800 PLATE
66. [2] 140252-0001 FLAT-HEAD SCREW
77. [1] 140241-4021 CONTROL SLEEVE
110. [1] 140420-2900 JOINT CONNECTION
111. [1] 026506-1040 GASKET
900. [1] 140191-1721 PLUNGER-AND-BARREL ASSY
900/5. [1] 140154-0420 PLUNGER-AND-BARREL ASSY M15
900/12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY K25
900/13. [1] 140112-2800 COMPRESSION SPRING
900/16. [1] 140115-2200 GASKET
900/17. [1] 140116-7220 FITTING
900/20. [1] 140118-0500 O-RING
900/30. [1] 140131-0021 FLANGE BUSHING
900/31. [1] 140271-0000 BEARING PIN
900/32. [2] 140118-0400 O-RING

Include in #2:

104207-1021 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104207-1021 
9 410 618 416 
NP-PFR1MD60/2NP9 
2566310300  FUJI-HEAVY
FUEL-INJECTION PUMP
K




Information:

1. Disconnect water supply hose from water pump inlet.2. Remove connector pipe (1), remove two bolts (2) and remove oil fill pipe (3). 3. Remove bolts (4) and (5) then remove the water pump. The following steps are for the installation of the water pump.4. Position the water pump and install two bolts (4) and (5). Tighten the two bolts evenly.5. Position connector pipe (1) and gaskets then install the bolts.6. Install oil fill pipe (3). Be sure the gasket is in position between the regulator and pipe and install bolts (2).End By:a. Install alternatorb. Fill the cooling system to the specified level. See the Maintenance ManualDisassemble & Assemble Water Pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump

Have questions with 104207-1021?





Group cross 104207-1021 ZEXEL

9 410 618 040 
NP-PFR1MD60/2NP7 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 618 119 
NP-PFR1MD60/2NP7 
2566310110 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 618 415 
NP-PFR1MD60/2NP8 
2566310200 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

104207-1021  
9 410 618 416 
NP-PFR1MD60/2NP9 
2566310300 
FUEL-INJECTION PUMP
Back to top