104207-1001 ZEXEL 9 410 618 119 BOSCH FUEL-INJECTION PUMP 9410618119 1042071001 2566310110


 

Information fuel-injection pump

BOSCH 9 410 618 119 9410618119
ZEXEL 104207-1001 1042071001
FUJI-HEAVY 2566310110 2566310110
104207-1001 FUEL-INJECTION PUMP
Rating:
22
Buy FUEL-INJECTION PUMP 104207-1001 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104207-1001
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105118-6960
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 19.1{195}
10. NOZZLE-HOLDER 105048-2040
11. NOZZLE 105017-3160

Scheme ###:

5. [1] 140154-0420 PLUNGER-AND-BARREL ASSY
12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
13. [1] 140112-2800 COMPRESSION SPRING
16. [1] 140115-2200 GASKET D12.8&8.6T0.5
17. [1] 140116-7220 FITTING
20. [1] 140118-0500 O-RING
30. [1] 140131-0021 FLANGE BUSHING
31. [1] 140271-0000 BEARING PIN
32. [2] 140118-0400 O-RING
37. [2] 140124-0100 FLAT-HEAD SCREW
40. [1] 140200-2320 TAPPET
44. [1] 140212-0500 BEARING PIN
45. [1] 140213-1300 LOCKING WASHER
50. [1] 140215-2000 COMPRESSION SPRING
51. [1] 140216-1300 SLOTTED WASHER
52. [1] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-3422 CONTROL ROD
65. [1] 140262-0800 PLATE
66. [2] 140252-0001 FLAT-HEAD SCREW
77. [1] 140241-4021 CONTROL SLEEVE
900. [1] 140191-1721 PLUNGER-AND-BARREL ASSY
900/5. [1] 140154-0420 PLUNGER-AND-BARREL ASSY
900/12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
900/13. [1] 140112-2800 COMPRESSION SPRING
900/16. [1] 140115-2200 GASKET D12.8&8.6T0.5
900/17. [1] 140116-7220 FITTING
900/20. [1] 140118-0500 O-RING
900/30. [1] 140131-0021 FLANGE BUSHING
900/31. [1] 140271-0000 BEARING PIN
900/32. [2] 140118-0400 O-RING

Include in #2:

104207-1001 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104207-1001 
9 410 618 119 
NP-PFR1MD60/2NP7 
2566310110  FUJI-HEAVY
FUEL-INJECTION PUMP
K 23MA FUEL INJECTION PUMP PFR-1MD PFR




Information:


Piston Group.(1) Crater. The piston is a symmetrical piston with an "on center" crater. Thoroughly lubricate piston group 360° in zone (A) with clean engine oil prior to inserting into the block group.(2) Top piston ring. Install ring with side marked "UP-1" toward top of piston (red color stripe to right of ring end gap).Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.625 0.190 mm (.0250 .0075 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)Minimum depth of groove in piston for top ring (new) ... 5.43 mm (.214 in)(3) Intermediate piston ring. Install ring with side marked "UP-2" toward top of piston (green color stripe to right of ring end gap).Width of groove in piston for intermediate ring (new) ... 3.061 0.013 mm (.1032 .0005 in)Minimum depth of groove in piston for intermediate ring (new) ... 5.43 mm (.214 in)Thickness of intermediate ring (new) ... 2.990 0.010 mm (.1177 .0004 in)Clearance between groove and intermediate ring (new) ... 0.048 to 0.094 mm (.0002 to .0037 in)Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.625 0.125 mm (.0250 .0050 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)(4) Oil regulating piston ring. Oil ring spring ends to be assembled 180° from ring end gap (orange colored portion of spring must be visible at ring end gap).Width of groove in piston for oil ring ... 4.033 0.013 mm (.1588 .0005 in)Minimum depth of groove in piston for oil ring (new) ... 3.727 mm (.1467 in)Thickness of oil ring (new) ... 3.987 0.013 mm (.1570 .0005 in)Clearance between groove and oil ring (new) ... 0.020 to 0.072 mm (.0008 to .0028 in)Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.44 0.15 mm (.017 .006 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)After piston rings have been installed, rotate rings so the end gaps are 120° apart.(5) Crown assembly.(6) Piston pin bore diameter in piston skirt ... 51.15 0.15 mm (2.014 .006 in)Thoroughly lubricate piston pin with clean engine oil prior to inserting into piston group and rod assembly.(7) Piston skirt.

Have questions with 104207-1001?





Group cross 104207-1001 ZEXEL

9 410 618 040 
NP-PFR1MD60/2NP7 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

104207-1001  
9 410 618 119 
NP-PFR1MD60/2NP7 
2566310110 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 618 415 
NP-PFR1MD60/2NP8 
2566310200 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 618 416 
NP-PFR1MD60/2NP9 
2566310300 
FUEL-INJECTION PUMP
Back to top