104206-1042 ZEXEL 9 410 618 116 BOSCH FUEL-INJECTION PUMP 9410618116 1042061042 2556310210


 

Information fuel-injection pump

BOSCH 9 410 618 116 9410618116
ZEXEL 104206-1042 1042061042
FUJI-HEAVY 2556310210 2556310210
104206-1042 FUEL-INJECTION PUMP
Rating:
78
Buy FUEL-INJECTION PUMP 104206-1042 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104206-1042
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105118-4610
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 19.1{195}
10. NOZZLE-HOLDER 105048-2040
11. NOZZLE 105017-0520

Scheme ###:

5. [1] 140154-1920 PLUNGER-AND-BARREL ASSY
12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
13. [1] 140112-2800 COMPRESSION SPRING
16. [1] 140115-2200 GASKET D12.8&8.6T0.5
17. [1] 140116-7220 FITTING
20. [1] 140118-0500 O-RING
30. [1] 140131-1121 FLANGE BUSHING
31. [1] 140271-0000 BEARING PIN
32. [2] 140118-0400 O-RING
37. [2] 140124-0100 FLAT-HEAD SCREW
40. [1] 140200-2320 TAPPET
44. [1] 140212-0500 BEARING PIN
45. [1] 140213-1300 LOCKING WASHER
50. [1] 140215-2000 COMPRESSION SPRING
51. [1] 140216-1300 SLOTTED WASHER
52. [1] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-3422 CONTROL ROD
65. [1] 140262-0800 PLATE
66. [2] 140252-0001 FLAT-HEAD SCREW
77. [1] 140241-4021 CONTROL SLEEVE
110. [1] 140420-2900 JOINT CONNECTION
111. [1] 026506-1040 GASKET D9.9&6.2T1
900. [1] 140191-1121 PLUNGER-AND-BARREL ASSY
900/5. [1] 140154-1920 PLUNGER-AND-BARREL ASSY
900/12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
900/13. [1] 140112-2800 COMPRESSION SPRING
900/16. [1] 140115-2200 GASKET D12.8&8.6T0.5
900/17. [1] 140116-7220 FITTING
900/20. [1] 140118-0500 O-RING
900/30. [1] 140131-1121 FLANGE BUSHING
900/31. [1] 140271-0000 BEARING PIN
900/32. [2] 140118-0400 O-RING

Include in #2:

104206-1042 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104206-1042 
9 410 618 116 
NP-PFR1MD55/2NP5 
2556310210  FUJI-HEAVY
FUEL-INJECTION PUMP
K 23MA FUEL INJECTION PUMP PFR-1MD PFR




Information:

1. Remove oil supply tube (1) and suction bell and tube (2). 2. Remove bolts (3) that hold the oil pump to the cylinder block, and remove oil pump (4). The following steps are for installation of the oil pump.3. Put oil pump (4) in position on the cylinder block. Install the bolts that hold the oil pump to the cylinder block.4. Put clean engine oil on the O-ring seals of the tubes.5. Install oil supply tube (1) and suction bell and tube (2).End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump1. Remove the bolt and washer that hold the gear on the shaft. 2. Use tooling (A), and remove drive gear (1) from the shaft. Remove the key from the shaft. 3. Remove retainer (3) for the bypass valve.4. Remove the spring and bypass valve.5. Remove cover (2) from the pump body. 6. Use tooling (B), and remove the bearings from the cover. 7. Remove gears (5) and (6) from pump body (4).8. Use tooling (B), and remove the bearings from pump body (4).Assemble Oil Pump
1. Use tooling (B) to install the bearings in the pump body. Install the bearings so the joint in the bearings is 30° 15° from the center line of the oil pump outlet passage (7). 2. Install idler gear (5) and drive gear (6) in the oil pump body. Put clean engine oil on the bearings and the gears. 3. Use tooling (B), and install the bearings in cover (2). Install the bearings so the joint in the bearings is 30° 15° from the center line of the bearing bores toward oil pump outlet passage (7).4. Install bypass valve (8), spring (9) and the retainer.5. Install the key on the shaft. 6. Install gear (1) on the shaft. Install the washer and bolt that hold the gear on the shaft. Be sure the pump turns freely after assembly.End By:a. install oil pump

Have questions with 104206-1042?





Group cross 104206-1042 ZEXEL

 
 

Fuji-Heavy 

 
2436310200 
FUEL-INJECTION PUMP
 
 

 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 617 085 
NP-PFR1MD55/2NP4 
2436310120 
FUEL-INJECTION PUMP
9 410 618 115 
NP-PFR1MD55/2NP4 
2436310130 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 617 185 
NP-PFR1MD55/2NP5 
2556310200 
FUEL-INJECTION PUMP
104206-1042  
9 410 618 116 
NP-PFR1MD55/2NP5 
2556310210 
FUEL-INJECTION PUMP
9 410 617 117 
NP-PFR1MD55/2NP6 
2556310300 
FUEL-INJECTION PUMP
9 410 618 117 
NP-PFR1MD55/2NP6 
2556310310 
FUEL-INJECTION PUMP
Back to top