104206-1032 ZEXEL 9 410 618 115 BOSCH FUEL-INJECTION PUMP 9410618115 1042061032 2436310130


 

Information fuel-injection pump

BOSCH 9 410 618 115 9410618115
ZEXEL 104206-1032 1042061032
FUJI-HEAVY 2436310130 2436310130
104206-1032 FUEL-INJECTION PUMP
Rating:
75
Buy FUEL-INJECTION PUMP 104206-1032 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104206-1032
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105118-4610
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 19.1{195}
10. NOZZLE-HOLDER 105048-2040
11. NOZZLE 105017-0520

Scheme ###:

5. [1] 140154-1920 PLUNGER-AND-BARREL ASSY
12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
13. [1] 140112-2800 COMPRESSION SPRING
16. [1] 140115-2200 GASKET D12.8&8.6T0.5
17. [1] 140116-7220 FITTING
20. [1] 140118-0500 O-RING
30. [1] 140131-0021 FLANGE BUSHING
31. [1] 140271-0000 BEARING PIN
32. [2] 140118-0400 O-RING
37. [2] 140124-0100 FLAT-HEAD SCREW
40. [1] 140200-2320 TAPPET
44. [1] 140212-0500 BEARING PIN
45. [1] 140213-1300 LOCKING WASHER
50. [1] 140215-2000 COMPRESSION SPRING
51. [1] 140216-1300 SLOTTED WASHER
52. [1] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-3422 CONTROL ROD
65. [1] 140262-0800 PLATE
66. [2] 140252-0001 FLAT-HEAD SCREW
77. [1] 140241-4021 CONTROL SLEEVE
110. [1] 140420-2400 BLEEDER SCREW
111. [1] 026506-1040 GASKET D9.9&6.2T1
900. [1] 140191-1021 PLUNGER-AND-BARREL ASSY
900/5. [1] 140154-1920 PLUNGER-AND-BARREL ASSY
900/12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
900/13. [1] 140112-2800 COMPRESSION SPRING
900/16. [1] 140115-2200 GASKET D12.8&8.6T0.5
900/17. [1] 140116-7220 FITTING
900/20. [1] 140118-0500 O-RING
900/30. [1] 140131-0021 FLANGE BUSHING
900/31. [1] 140271-0000 BEARING PIN
900/32. [2] 140118-0400 O-RING

Include in #2:

104206-1032 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104206-1032 
9 410 618 115 
NP-PFR1MD55/2NP4 
2436310130  FUJI-HEAVY
FUEL-INJECTION PUMP
K 23MA FUEL INJECTION PUMP PFR-1MD PFR




Information:

Start By:a. remove valve covers 1. Use tooling (A), and disconnect fuel line (1) at each end. Remove the fuel line from the engine. 2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. Install the 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and on seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tooling (A) to a torque of 40 7 N m (30 5 lb.ft.).End By:a. install valve covers

Have questions with 104206-1032?





Group cross 104206-1032 ZEXEL

 
 

Fuji-Heavy 

 
2436310200 
FUEL-INJECTION PUMP
 
 

 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 617 085 
NP-PFR1MD55/2NP4 
2436310120 
FUEL-INJECTION PUMP
104206-1032  
9 410 618 115 
NP-PFR1MD55/2NP4 
2436310130 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Fuji-Heavy 

9 410 617 185 
NP-PFR1MD55/2NP5 
2556310200 
FUEL-INJECTION PUMP
9 410 618 116 
NP-PFR1MD55/2NP5 
2556310210 
FUEL-INJECTION PUMP
9 410 617 117 
NP-PFR1MD55/2NP6 
2556310300 
FUEL-INJECTION PUMP
9 410 618 117 
NP-PFR1MD55/2NP6 
2556310310 
FUEL-INJECTION PUMP
Back to top