Buy 104205-4100 ZEXEL 9 410 617 329 BOSCH FUEL-INJECTION PUMP 9410617329 1042054100 1625951012


 

Information fuel-injection pump

BOSCH 9 410 617 329 9410617329
ZEXEL 104205-4100 1042054100
KUBOTA 1625951012 1625951012
104205-4100 FUEL-INJECTION PUMP
Rating:
66
Buy FUEL-INJECTION PUMP 104205-4100 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$699.00

16 Jan 2025

CN: qian cheng
Fuel Injection Pump 16259-51010 16259-51011 16259-51012 16259-51013 16259-51014 for Kubota Engine V1305 V1505 V1305-BBS
ADPelcote Part number:16259-51010 || Applications:for Kubota Engine V1305 V1505 V1305-BBS

Components :

0. INJECTION-PUMP ASSEMBLY 104205-4100
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

5. [4] 140154-0720 PLUNGER-AND-BARREL ASSY
12. [4] 140110-4420 DELIVERY-VALVE ASSEMBLY
13. [4] 140112-2800 COMPRESSION SPRING
16. [4] 140115-2200 GASKET D12.8&8.6T0.5
17. [4] 140116-7220 FITTING
20. [4] 016550-1220 O-RING
30. [4] 140131-0020 FLANGE BUSHING
31. [4] 140271-0000 BEARING PIN
32. [8] 016550-1620 O-RING
37. [8] 140124-0100 FLAT-HEAD SCREW
40. [4] 140200-2320 TAPPET
44. [4] 140212-0300 BEARING PIN
45. [1] 140213-1200 LOCKING WASHER
50. [4] 140215-2000 COMPRESSION SPRING
51. [4] 140216-1300 SLOTTED WASHER
52. [4] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-5920 CONTROL ROD
65. [1] 140262-1000 PLATE
66. [5] 140252-0000 FLAT-HEAD SCREW
77. [4] 140241-4021 CONTROL SLEEVE
93. [1] 140402-2721 EYE BOLT

Include in #2:

104205-4100 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104205-4100 
104205-4101 
9 410 617 329 
1625951012  KUBOTA
FUEL-INJECTION PUMP
* K 23MD PFR-4MD PFR




Information:

37. Remove dowels (72) and flyweights (73) from the carrier assembly.38. Remove dowel (71) from the governor shaft, and remove the governor shaft from the carrier assembly. 39. Remove races (74) and (76) and bearing (75) from the camshaft in the fuel injection pump housing.Assemble Governor
1. Put the fuel injection pump housing in position on tool (A). Install race (76) bearing (75) and race (74) on the end of the camshaft in the fuel injection pump housing. 2. Put flyweights (73) in position on carrier assembly (70), and install dowels (72) to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.230 mm (.0004 to .0090 in.) end play. 3. Install governor shaft (77) on carrier assembly (70). 4. Install dowel (71) in governor shaft (77) and slide carrier assembly (70) down on the governor shaft until dowel (71) fits into the slot in the carrier assembly.5. Install carrier assembly (70) on the end of the camshaft. 6. Install race (68), bearing (69), race (68) and ring (67) on riser (65). 7. Install riser (65) and spring (66), if equipped, on the governor shaft. 8. Install spool (62) and ring (63) on seat (61) and use tool (B) to install ring (64) to hold them in position.9. Install seat (61) on spring (60). Install spring (60) on shield (59). 10. Install dashpot assembly (58) on the governor shaft. 11. Install ring (57) in the groove on the governor shaft. Install sleeve (78), spring (55), the sleeve and bearing (56) on the governor shaft. 12. Use tool (C) to hold spring (55) under compression, and install the ring in the groove on the governor shaft. 13. Put lever (52) in position on governor servo (53), and install pin (51) to hold the lever in place. Use a hammer and chisel to move the metal (stake) four places 90° apart on the outside surface on both legs of the governor servo to hold pin (51) in place.14. Install O-ring seal (54) on sleeve (48). Install piston (50) and sleeve (48) in the governor servo as shown.15. Install valve (49) in the governor servo as shown. 16. Install lockring (42) in the groove near the center of valve (43). Put sleeve (44), spring (broken link spring) (45) and seat (46) in position on valve (43), and install lockring (47) to hold them in place. 17. Put governor servo (41) in position on the fuel injection pump housing with piston (50) engaged over the rack. Make sure the lever is engaged in the (slot) groove of riser (65). 18. If dowel (82) was removed, install it in block (83) 31 0.5 mm (1.22 .02 in.) above the outside surface of the block.19. Install bolt (40) in block (83) and spring (38) on bolt (40).20. Install stop screw (80) and the locknut on collar (39). Install power setting screw (81) and the locknut on the collar.21. Install collar (39) on bolt (40). Make

Have questions with 104205-4100?





Group cross 104205-4100 ZEXEL

Kubota 

104205-4100  

104205-4101 
9 410 617 329 
1625951012 
FUEL-INJECTION PUMP
9 410 617 231 
NP-PFR4MD50/1NP11 
1625951013 
FUEL-INJECTION PUMP
9 410 617 330 
1753451011 
FUEL-INJECTION PUMP
9 410 618 219 
NP-PFR4MD50/1NP12 
1753451012 
FUEL-INJECTION PUMP
Back to top