Buy 104205-4052 ZEXEL 9 410 617 228 BOSCH FUEL-INJECTION PUMP 9410617228 1042054052 1628251012


 

Information fuel-injection pump

BOSCH 9 410 617 228 9410617228
ZEXEL 104205-4052 1042054052
KUBOTA 1628251012 1628251012
104205-4052 FUEL-INJECTION PUMP
Rating:
58
Buy FUEL-INJECTION PUMP 104205-4052 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
£513.19
 

25 Oct 2018

Robert Bos: Robert Bosch GmbH Au
Bosch 9410617228 Fuel-Injection Pump
Preparation of fuel injection pump: online || Fuel Type: Diesel

Components :

0. INJECTION-PUMP ASSEMBLY 104205-4052
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

5. [4] 140154-1420 PLUNGER-AND-BARREL ASSY
12. [4] 140110-4420 DELIVERY-VALVE ASSEMBLY
13. [4] 140112-2800 COMPRESSION SPRING
16. [4] 140115-2200 GASKET D12.8&8.6T0.5
17. [4] 140116-7220 FITTING
20. [4] 140118-0500 O-RING
30. [4] 140131-0021 FLANGE BUSHING
31. [4] 140271-0000 BEARING PIN
32. [8] 140118-0400 O-RING
37. [8] 140124-0100 FLAT-HEAD SCREW
40. [4] 140200-2320 TAPPET
44. [4] 140212-0300 BEARING PIN
45. [1] 140213-1200 LOCKING WASHER
50. [4] 140215-2000 COMPRESSION SPRING
51. [4] 140216-1300 SLOTTED WASHER
52. [4] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-7020 CONTROL ROD
65. [1] 140262-1301 PLATE
66. [5] 140252-0001 FLAT-HEAD SCREW
77. [4] 140241-4021 CONTROL SLEEVE
93. [1] 140402-2921 EYE BOLT
93/1. [1] 140402-2901 EYE BOLT
93/2. [2] 026510-1340 GASKET D13.4&10.2T1
900. [4] 140191-0320 PLUNGER-AND-BARREL ASSY
900/5. [1] 140154-1420 PLUNGER-AND-BARREL ASSY
900/12. [1] 140110-4420 DELIVERY-VALVE ASSEMBLY
900/13. [1] 140112-2800 COMPRESSION SPRING
900/16. [1] 140115-2200 GASKET D12.8&8.6T0.5
900/17. [1] 140116-7220 FITTING
900/20. [1] 140118-0500 O-RING
900/30. [1] 140131-0021 FLANGE BUSHING
900/31. [1] 140271-0000 BEARING PIN
900/32. [2] 140118-0400 O-RING

Include in #2:

104205-4052 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104205-4052 
9 410 617 228 
NP-PFR4MD50/NP6 
1628251012  KUBOTA
FUEL-INJECTION PUMP
K 23MD FUEL INJECTION PUMP PFR-4MD PFR




Information:

Start By:a. remove cylinder headb. remove oil panc. remove cooling jets 1. Remove two rod cap bolts (1) from each rod. Remove rod caps (2).2. Using a soft hammer tape rod (3) away from crankshaft and remove bearing half (4). When removing cylinder pack, watch the rod and prevent it from catching on the block bore as it comes out.3. Install tooling (A) and remove cylinder pack (5). 4. Remove cylinder liner seal (6) at the base of the spacer block. 5. Remove the remainder of tooling (A) from cylinder pack (5) and then remove the rod and piston from the cylinder liner. The following steps are for the installation of the cylinder pack.6. Install a new cylinder liner seal, lubricate the seal with engine oil. Some engines use pistons which have the word "FRONT" stamped on the crown of the piston. Make sure the word "FRONT" is toward the front of the engine when the piston is installed. The etched number on the connecting rod must be on the right side and must be installed in the corresponding cylinder. 9U-5839 Liquid Gasket Material is applied to the cylinder liners in the area shown in the illustration. The liquid gasket material helps prevent oil leaks from between the cylinder block and spacer block. DO NOT apply any 9U-5839 Liquid Gasket Material between the engine spacer block and the cylinder block surfaces. Using excessive amounts of liquid gasket material on the liner flange seat can cause oil leaks due to distortion of the O-ring seals between the spacer block and cylinder block.7. Lubricate the lower portion of the cylinder liner with engine oil. Be sure the corresponding crankshaft throw is at bottom center. Position cylinder pack (5) and guide rod (3) into place. Use tooling (B) and press cylinder pack (5) into place.8. With rod (3) in this position, install the upper half of rod bearing (4). Be sure the bearing tab properly engages the slot in the connecting rod. Lubricate the bearing surface with engine oil and tap the piston down with a rubber mallet until the rod and bearing contacts the crankshaft.9. With rod cap bearing in place and oiled, install rod cap (2). Lubricate rod bolts (1) with 2P2506 Thread Lubricant. Install rod bolts (1) and torque to 130 7 N m (95 5 lb.ft.). Mark each bolt head and then tighten each bolt an additional 60 5° (1/6 turn).End By:a. install cooling jets.b. install oil pan.c. install cylinder head.

Have questions with 104205-4052?





Group cross 104205-4052 ZEXEL

Kubota 

 
1509451012 
FUEL-INJECTION PUMP
 
1509451012 
FUEL-INJECTION PUMP
 
1588151011 
FUEL-INJECTION PUMP
9 410 617 323 
1588151012 
FUEL-INJECTION PUMP
9 410 617 324 
1588151013 
FUEL-INJECTION PUMP

Kubota-Extra 

9 410 617 324 
1588151013 
FUEL-INJECTION PUMP

Kubota 

 
162715101 
FUEL-INJECTION PUMP
 
1627151012 
FUEL-INJECTION PUMP
9 410 617 325 
1627151013 
FUEL-INJECTION PUMP
9 410 617 325 
1627151014 
FUEL-INJECTION PUMP
9 410 617 227 
NP-PFR4MD50/1NP4 
1627151015 
FUEL-INJECTION PUMP
9 410 617 326 
1628251011 
FUEL-INJECTION PUMP
104205-4052  
9 410 617 228 
NP-PFR4MD50/NP6 
1628251012 
FUEL-INJECTION PUMP
 
1628551011 
FUEL-INJECTION PUMP
9 410 617 327 
 
FUEL-INJECTION PUMP

Kubota 

9 410 617 056 
1625951011 
FUEL-INJECTION PUMP
9 410 617 328 
1669551101 
FUEL-INJECTION PUMP
9 410 617 229 
NP-PFR4MD50/1NP9 
1669551981 
FUEL-INJECTION PUMP
9 410 617 077 
1628551012 
FUEL-INJECTION PUMP
9 410 617 230 
NP-PFR4MD50/1NP10 
 
FUEL-INJECTION PUMP
Back to top