104205-4013 ZEXEL 9 410 617 324 BOSCH FUEL-INJECTION PUMP 9410617324 1042054013 1588151013

Information fuel-injection pump

BOSCH 9 410 617 324 9410617324

ZEXEL 104205-4013 1042054013

KUBOTA 1588151013 1588151013

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104205-4013 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104205-4013
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

5.	[4]	140153-9120	PLUNGER-AND-BARREL ASSY
12.	[4]	140110-4420	DELIVERY-VALVE ASSEMBLY
13.	[4]	140112-2800	COMPRESSION SPRING
16.	[4]	140115-2200	GASKET D12.8&8.6T0.5
17.	[4]	140116-6900	FITTING
20.	[4]	016550-1220	O-RING
30.	[4]	140131-0021	FLANGE BUSHING
31.	[4]	140271-0000	BEARING PIN
32.	[8]	016550-1620	O-RING
37.	[8]	140124-0100	FLAT-HEAD SCREW
40.	[4]	140200-2320	TAPPET
44.	[4]	140212-0300	BEARING PIN
45.	[1]	140213-1200	LOCKING WASHER
50.	[4]	140215-2000	COMPRESSION SPRING
51.	[4]	140216-1300	SLOTTED WASHER
52.	[4]	140254-2900	SLOTTED WASHER
53/1.	[1]	140254-1400	PLATE T1.80
53/1.	[1]	140254-1500	PLATE T1.85
53/1.	[1]	140254-1600	PLATE T1.90
53/1.	[1]	140254-1700	PLATE T1.95
53/1.	[1]	140254-1800	PLATE T2.00
53/1.	[1]	140254-1900	PLATE T2.05
53/1.	[1]	140254-2000	PLATE T2.10
53/1.	[1]	140254-2100	PLATE T2.15
53/1.	[1]	140254-2200	PLATE T2.20
53/1.	[1]	140254-2300	PLATE T2.25
53/1.	[1]	140254-2400	PLATE T2.30
53/1.	[1]	140254-2500	PLATE T2.35
53/1.	[1]	140254-2600	PLATE T2.40
53/1.	[1]	140254-2700	PLATE T2.45
53/1.	[1]	140254-2800	PLATE T2.50
53/1.	[1]	140254-3100	PLATE T1.825
53/1.	[1]	140254-3200	PLATE T1.875
53/1.	[1]	140254-3300	PLATE T1.925
53/1.	[1]	140254-3400	PLATE T1.975
53/1.	[1]	140254-3500	PLATE T2.025
53/1.	[1]	140254-3600	PLATE T2.075
53/1.	[1]	140254-3700	PLATE T2.125
53/1.	[1]	140254-3800	PLATE T2.175
53/1.	[1]	140254-3900	PLATE T2.225
53/1.	[1]	140254-4000	PLATE T2.275
53/1.	[1]	140254-4100	PLATE T2.325
53/1.	[1]	140254-4200	PLATE T2.375
53/1.	[1]	140254-4300	PLATE T2.425
53/1.	[1]	140254-4400	PLATE T2.475
53/1.	[1]	140254-4500	PLATE T2.525
60.	[1]	140243-5320	CONTROL ROD
65.	[1]	140262-0300	PLATE
66.	[5]	140252-0000	FLAT-HEAD SCREW
77.	[4]	140241-4021	CONTROL SLEEVE
93.	[1]	140402-3020	EYE BOLT

Include in #1:

103684-0280 as _

Include in #2:

104205-4013 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

104205-4013

9 410 617 324

1588151013 KUBOTA

FUEL-INJECTION PUMP
K 23MD FUEL INJECTION PUMP PFR-4MD PFR

104205-4013

9 410 617 324

1588151013 KUBOTA-EXTRA

FUEL-INJECTION PUMP
K 23MD FUEL INJECTION PUMP PFR-4MD PFR

Information:

1. Disconnect water supply hose from water pump inlet.2. Remove connector pipe (1), remove two bolts (2) and remove oil fill pipe (3). 3. Remove bolts (4) and (5) then remove the water pump. The following steps are for the installation of the water pump.4. Position the water pump and install two bolts (5) and (6). Tighten the two bolts evenly.5. Position connector pipe (1) and gaskets then install the bolts.6. Install oil fill pipe (3). Be sure the gasket is in position between the regulator and pipe and install bolts (2).End By:a. Install alternator (if removed)b. Fill the cooling system to the specified level. See the Maintenance Manual.Disassemble And Assemble Water Pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in.).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump