Information fuel-injection pump
BOSCH
9 410 617 323
9410617323
ZEXEL
104205-4012
1042054012
KUBOTA
1588151012
1588151012

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104205-4012 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [4] | 140153-9120 | PLUNGER-AND-BARREL ASSY |
12. | [4] | 140110-4420 | DELIVERY-VALVE ASSEMBLY |
13. | [4] | 140112-2800 | COMPRESSION SPRING |
16. | [4] | 140115-2200 | GASKET D12.8&8.6T0.5 |
17. | [4] | 140116-6900 | FITTING |
20. | [4] | 016550-1220 | O-RING |
30. | [4] | 140131-0020 | FLANGE BUSHING |
31. | [4] | 140271-0000 | BEARING PIN |
32. | [8] | 016550-1620 | O-RING |
37. | [8] | 140124-0100 | FLAT-HEAD SCREW |
40. | [4] | 140200-2320 | TAPPET |
44. | [4] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-1200 | LOCKING WASHER |
50. | [4] | 140215-2000 | COMPRESSION SPRING |
51. | [4] | 140216-1300 | SLOTTED WASHER |
52. | [4] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-5320 | CONTROL ROD |
65. | [1] | 140262-0300 | PLATE |
66. | [5] | 140252-0000 | FLAT-HEAD SCREW |
77. | [4] | 140241-4020 | CONTROL SLEEVE |
93. | [1] | 140402-3020 | EYE BOLT |
Include in #1:
103684-0290
as _
Include in #2:
104205-4012
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
1. Remove oil filter elements (1). 2. Remove two bolts (2).3. Remove four bolts (3).4. Remove six bolts (4) then remove oil filter base, gaskets and o-rings. The following steps are for the installation of the oil filter and oil filter base. Position gaskets and install all bolts finger tight before tightening to the standard torque.5. Be sure the o-rings are in place on oil filter base. Position gaskets and oil filter base, then install bolts (4).6. Install bolts (3).7. Position gasket and install bolts (2). Then tighten all the bolts to standard torque.8. Install oil filter elements (1).Oil Filter Base, Disassemble And Assemble
Start By:a. remove oil filter base 1. Remove the o-rings and remove bolt (1). 2. Remove relief valve group (2). 3. Remove four bolts and remove covers (3). Remove oil cooler by-pass valve (5), oil cooler by-pass valve spring (4) and spool (6). 4. Remove plug (7) and remove oil filter by-pass valve (8). The following steps are for the assembly of the oil filter base.5. Install by-pass valve (8) and plug (7).6. Install oil cooler by-pass valve (5), oil pump by-pass valve (6) and spring (4), then position covers (3) and install bolts.7. Position relief valve group (2) and install bolt (1). Install o-ring seals.End By:a. install oil filter base
Start By:a. remove oil filter base 1. Remove the o-rings and remove bolt (1). 2. Remove relief valve group (2). 3. Remove four bolts and remove covers (3). Remove oil cooler by-pass valve (5), oil cooler by-pass valve spring (4) and spool (6). 4. Remove plug (7) and remove oil filter by-pass valve (8). The following steps are for the assembly of the oil filter base.5. Install by-pass valve (8) and plug (7).6. Install oil cooler by-pass valve (5), oil pump by-pass valve (6) and spring (4), then position covers (3) and install bolts.7. Position relief valve group (2) and install bolt (1). Install o-ring seals.End By:a. install oil filter base