104205-3110 ZEXEL 9 410 617 663 BOSCH FUEL-INJECTION PUMP 9410617663 1042053110


 

Information fuel-injection pump

BOSCH 9 410 617 663 9410617663
ZEXEL 104205-3110 1042053110
104205-3110 FUEL-INJECTION PUMP
Rating:
35
Buy FUEL-INJECTION PUMP 104205-3110 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104205-3110
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105148-1132
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 11.8{120}
10. NOZZLE-HOLDER 105078-0062
11. NOZZLE 105007-1140

Scheme ###:

5. [3] 140154-9620 PLUNGER-AND-BARREL ASSY
12. [3] 140110-3620 DELIVERY-VALVE ASSEMBLY
13. [3] 140112-2800 COMPRESSION SPRING
16. [3] 140115-2200 GASKET D12.8&8.6T0.5
17. [3] 140116-7220 FITTING
20. [3] 016550-1220 O-RING
30. [3] 140131-0021 FLANGE BUSHING
31. [3] 140271-0000 BEARING PIN
32. [6] 016550-1620 O-RING
37. [6] 140124-0100 FLAT-HEAD SCREW
40. [3] 140200-2320 TAPPET
44. [3] 140212-0300 BEARING PIN
45. [1] 140213-0900 LOCKING WASHER
50. [3] 140215-2000 COMPRESSION SPRING
51. [3] 140216-1300 SLOTTED WASHER
52. [3] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-2721 CONTROL ROD
65. [1] 140262-0500 PLATE
66. [4] 140252-0000 FLAT-HEAD SCREW
77. [3] 140241-4021 CONTROL SLEEVE
93. [1] 140402-1820 EYE BOLT
110. [1] 140420-2400 BLEEDER SCREW
111. [1] 026506-1040 GASKET D9.9&6.2T1
170. [1] 140405-0100 CAPSULE
171. [1] 026510-1340 GASKET D13.4&10.2T1

Include in #2:

104205-3110 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104205-3110 
104205-3111 
9 410 617 663 
   
FUEL-INJECTION PUMP
* K




Information:

(1) Distance dowels extend past end surface of cylinder block ... 8.0 0.5 mm (.31 .02 in)(2) Bore diameter in cylinder block for the cylinder liners ... 136.00 0.03 mm (5.354 .001 in)(3) Distance dowels extend past end surface of cylinder block ... 8.0 0.5 mm (.31 .02 in) (4) Spacer block.(5) Height of dowels above top surface of spacer block and cylinder block ... 8.00 0.03 mm (.315 .001 in)(6) Cylinder Liner. Make reference to the procedure for checking Cylinder Liner Projection in Testing And Adjusting Section of Service Manual Form No. SENR3909.Cylinder liner projection above the top surface of the spacer block must be ... 0.12 0.08 mm (.005 .003 in) Apply 7M7260 Liquid Gasket as required to cylinder liner shoulder and cylinder block face joint of all liners. (7) Depth plug is to be installed (from end surface of cylinder block to top of plug) ... 1.25 0.25 mm (.049 .010 in)(8) Diameter of camshaft bores ... 75.000 0.025 mm (2.9530 .0010 in)(9) Oil cooling jet assembly. Tighten bolt that holds oil cooling jet to ... 25 7 N m (18 5 lb ft)(10) Width of main bearing cap ... 175.00 0.02 mm (6.8898 .0008 in)Width in cylinder block for main bearing cap ... 175.000 0.018 mm (6.8898 .0007 in)(11) Distance from centerline of crankshaft bore to top surface of cylinder block ... 265.0 mm (10.43 in)The flatness across the top contact surface of the block must be within 0.05 mm (.002 in) for any 150 mm (5.9 in) section of the surface.(12) Distance from centerline of crankshaft to bottom surface of cylinder block ... 120.0 mm (4.72 in)(13) Main bearing cap bolts. Install as follows:Main bearing caps shall be assembled with the part number towards the right side. Caps are to be identified by stamped numbers 1 thru 7 located on the bottom unmachined surface.Main bearing cap bolts to be lubricated on threads and washer face with SAE 30 oil or molylube. Tighten bolts to 95 5 N m (70 4 lb ft) plus 90 5° additional turnprior to machining. Tighten bolts simultaneously or tighten both bolts to 95 N m (70 lb ft) before turning the additional 90°.(14) Bore in cylinder block for seven main bearings ... 108.000 0.013 mm (4.2520 .0005 in) All main bearing bore measurements are to be made before caps are disassembled.

Have questions with 104205-3110?





Group cross 104205-3110 ZEXEL

9 410 617 662 
 
FUEL-INJECTION PUMP

Iseki 

9 410 618 411 
NP-PFR3MD50/1NP16 
62156001090A 
FUEL-INJECTION PUMP
104205-3110  

104205-3111 
9 410 617 663 
 
FUEL-INJECTION PUMP

Iseki 

9 410 618 412 
NP-PFR3MD50/1NP17 
62156001130 
FUEL-INJECTION PUMP
9 410 617 116 
62156001091E 
FUEL-INJECTION PUMP
9 410 617 226 
NP-PFR3MD50/1NP19 
62156001092F 
FUEL-INJECTION PUMP
9 410 618 106 
NP-PFR3MD50/1NP19 
62156001093G 
FUEL-INJECTION PUMP

Kubota 

9 410 618 413 
NP-PFR3MD50/1NP20 
1G82051011 
FUEL-INJECTION PUMP
9 410 618 414 
NP-PFR3MD50/1NP20 
1G82051012 
FUEL-INJECTION PUMP
F 01G 09Y 01X 
NP-PFR3MD50/1NP22 
1600651012 
FUEL-INJECTION PUMP
F 01G 09Y 01X 
NP-PFR3MD50/1NP22 
1G43451011 
FUEL-INJECTION PUMP
F 01G 09Y 01Y 
NP-PFR3MD50/1NP23 
1G82051013 
FUEL-INJECTION PUMP
F 01G 09Y 01Y 
NP-PFR3MD50/1NP23 
1G00651011 
FUEL-INJECTION PUMP
Back to top