Information fuel-injection pump
BOSCH
9 410 618 407
9410618407
ZEXEL
104205-2081
1042052081
KUBOTA
1G99151011
1g99151011

Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Fuel Injection Pump 1G991-51011 for Kubota Engine
AUCALIWI Part number:1G991-51011 || Application:for Kubota Engine
AUCALIWI Part number:1G991-51011 || Application:for Kubota Engine
FridayParts Fuel Injection Pump 1G991-51011 1G99151011 Compatible for Kubota Engine Replacement
FP FRIDAYPARTS New aftermarket parts, the picture is just for reference. || Part Number:1G991-51011 1G99151011 104205-2081 1042052081 || Compatible for Kubota Engine || Please verify your part number before ordering, if you have any question please don't hesitate to contact us.
FP FRIDAYPARTS New aftermarket parts, the picture is just for reference. || Part Number:1G991-51011 1G99151011 104205-2081 1042052081 || Compatible for Kubota Engine || Please verify your part number before ordering, if you have any question please don't hesitate to contact us.
Components :
0. | INJECTION-PUMP ASSEMBLY | 104205-2081 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [2] | 140161-0220 | PLUNGER-AND-BARREL ASSY M31 |
12. | [2] | 140110-4420 | DELIVERY-VALVE ASSEMBLY K25 |
13. | [2] | 140112-2800 | COMPRESSION SPRING |
16. | [2] | 140115-2200 | GASKET |
17. | [2] | 140116-7820 | FITTING |
20. | [2] | 140118-0500 | O-RING |
30. | [2] | 140131-0021 | FLANGE BUSHING |
31. | [2] | 140271-0000 | BEARING PIN |
32. | [4] | 140118-0400 | O-RING |
37. | [4] | 140124-0100 | FLAT-HEAD SCREW |
40. | [2] | 140200-2320 | TAPPET |
44. | [2] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-0800 | LOCKING WASHER |
50. | [2] | 140215-2000 | COMPRESSION SPRING |
51. | [2] | 140216-1300 | SLOTTED WASHER |
52. | [2] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-3620 | CONTROL ROD |
65. | [1] | 140262-0401 | PLATE |
66. | [4] | 140252-0001 | FLAT-HEAD SCREW |
77. | [2] | 140241-4021 | CONTROL SLEEVE |
93. | [1] | 140402-3020 | EYE BOLT |
93/1. | [1] | 140402-3000 | EYE BOLT |
93/2. | [2] | 026510-1340 | GASKET |
93/3. | [1] | 140420-2400 | BLEEDER SCREW |
93/4. | [1] | 026506-1040 | GASKET |
900. | [2] | 140191-1820 | PLUNGER-AND-BARREL ASSY |
900/5. | [2] | 140161-0220 | PLUNGER-AND-BARREL ASSY M31 |
900/12. | [2] | 140110-4420 | DELIVERY-VALVE ASSEMBLY K25 |
900/13. | [2] | 140112-2800 | COMPRESSION SPRING |
900/16. | [2] | 140115-2200 | GASKET |
900/17. | [2] | 140116-7820 | FITTING |
900/20. | [2] | 140118-0500 | O-RING |
900/30. | [2] | 140131-0021 | FLANGE BUSHING |
900/31. | [2] | 140271-0000 | BEARING PIN |
900/32. | [4] | 140118-0400 | O-RING |
Include in #1:
101607-1260
as _
Include in #2:
104205-2081
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
3. Loosen the clamps on breather tube (1) and pull it back for clearance. 4. Remove bolt (2) from the cover on the side of the cylinder block. 5. Remove the three bolts that hold cover (3) to the water pump. Remove cover (3) from the water pump. 6. Remove the two bolts, and remove elbow (4) from bonnet (5). Remove the two bolts, and remove bonnet (5) from the water pump. It is not necessary to remove bolts (6). These bolts only hold the cover to the timing gear cover.7. Remove six long bolts (7) that hold the water pump to the timing gear cover. Remove water pump (8).Install Water Pump
1. Check the O-ring seals and gaskets, and make replacements if needed. 2. Make sure O-ring seal (9) is in position on the water pump. Put water pump (8) into position in the timing gear cover. Install the bolts that hold the water pump in place. 3. Make sure the gaskets are in place. Connect bonnet (5) to the water pump. Connect elbow (4) to the bonnet. 4. Make sure O-ring seal (10) is in position, and install cover (3) on the water pump. 5. Install bolt (2) on the cover on the side of the engine. 6. Put breather tube (1) in position, and install the clamps that hold it.7. Install the alternator mounting group and alternator on the engine.8. Install the water temperature regulator and manifold. See the topic Install Water Temperature Regulator and Manifold.9. Fill cooling system to the correct level. See the Maintenance Guide.Disassemble And Assemble Water Pump
Start By: The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not and indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) an washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14), and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10), and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over, and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal
1. Check the O-ring seals and gaskets, and make replacements if needed. 2. Make sure O-ring seal (9) is in position on the water pump. Put water pump (8) into position in the timing gear cover. Install the bolts that hold the water pump in place. 3. Make sure the gaskets are in place. Connect bonnet (5) to the water pump. Connect elbow (4) to the bonnet. 4. Make sure O-ring seal (10) is in position, and install cover (3) on the water pump. 5. Install bolt (2) on the cover on the side of the engine. 6. Put breather tube (1) in position, and install the clamps that hold it.7. Install the alternator mounting group and alternator on the engine.8. Install the water temperature regulator and manifold. See the topic Install Water Temperature Regulator and Manifold.9. Fill cooling system to the correct level. See the Maintenance Guide.Disassemble And Assemble Water Pump
Start By: The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not and indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) an washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14), and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10), and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over, and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal