Information fuel-injection pump
BOSCH
9 410 618 405
9410618405
ZEXEL
104205-2072
1042052072
KUBOTA
1900751012
1900751012

Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IMIFAFTAbT 19007-51012 19007-51010 104205-2071 Fuel Injection Pump for Kubota Z482 Z482-B-F Engine
IMIFAFTAbT Part Name:Fuel Injection Pump 19007-51012 19007-51010 104205-2071 || Part Number:19007-51012 19007-51010 104205-2071 9410617080 || APPlication: Compatible with Kubota Z482 Z482-B-F Engine || If you are not sure if the product is suitable please leave us a message and send us your original || product picture and part number and we will send the correct part after confirmation
IMIFAFTAbT Part Name:Fuel Injection Pump 19007-51012 19007-51010 104205-2071 || Part Number:19007-51012 19007-51010 104205-2071 9410617080 || APPlication: Compatible with Kubota Z482 Z482-B-F Engine || If you are not sure if the product is suitable please leave us a message and send us your original || product picture and part number and we will send the correct part after confirmation
IMELBUFF 19007-51012 19007-51010 104205-2071 9410617080 Fuel Injection Pump for Z482 Z482-B-F Engine
IMELBUFF 🚜Part Number: 19007-51012 19007-51010 104205-2071 9410617080 || 🚜Engine Model: for Z482 Z482-B-F Engine || 🚜Part Type: Z482 Engine Fuel Injection Pump || 🚜Warm Tips: Please check your part numbers before placing an order. If you are not sure, you can send us your engine model or fuel pump part number || 🚜Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
IMELBUFF 🚜Part Number: 19007-51012 19007-51010 104205-2071 9410617080 || 🚜Engine Model: for Z482 Z482-B-F Engine || 🚜Part Type: Z482 Engine Fuel Injection Pump || 🚜Warm Tips: Please check your part numbers before placing an order. If you are not sure, you can send us your engine model or fuel pump part number || 🚜Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
Components :
0. | INJECTION-PUMP ASSEMBLY | 104205-2072 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [2] | 140154-1720 | PLUNGER-AND-BARREL ASSY |
12. | [2] | 140110-4420 | DELIVERY-VALVE ASSEMBLY |
13. | [2] | 140112-2800 | COMPRESSION SPRING |
16. | [2] | 140115-2200 | GASKET D12.8&8.6T0.5 |
17. | [2] | 140116-7820 | FITTING |
20. | [2] | 140118-0500 | O-RING |
30. | [2] | 140131-0021 | FLANGE BUSHING |
31. | [2] | 140271-0000 | BEARING PIN |
32. | [4] | 140118-0400 | O-RING |
37. | [4] | 140124-0100 | FLAT-HEAD SCREW |
40. | [2] | 140200-2320 | TAPPET |
44. | [2] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-0800 | LOCKING WASHER |
50. | [2] | 140215-2000 | COMPRESSION SPRING |
51. | [2] | 140216-1300 | SLOTTED WASHER |
52. | [2] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-3620 | CONTROL ROD |
65. | [1] | 140262-0401 | PLATE |
66. | [4] | 140252-0001 | FLAT-HEAD SCREW |
77. | [2] | 140241-4021 | CONTROL SLEEVE |
93. | [1] | 140402-3222 | EYE BOLT |
93/1. | [1] | 140402-3202 | EYE BOLT |
93/2. | [2] | 026510-1340 | GASKET D13.4&10.2T1 |
93/3. | [1] | 140420-1400 | BLEEDER SCREW |
93/4. | [1] | 026508-1240 | GASKET D11.9&8.2T1 |
900. | [2] | 140191-0720 | PLUNGER-AND-BARREL ASSY |
900/5. | [1] | 140154-1720 | PLUNGER-AND-BARREL ASSY |
900/12. | [1] | 140110-4420 | DELIVERY-VALVE ASSEMBLY |
900/13. | [1] | 140112-2800 | COMPRESSION SPRING |
900/16. | [1] | 140115-2200 | GASKET D12.8&8.6T0.5 |
900/17. | [1] | 140116-7820 | FITTING |
900/20. | [1] | 140118-0500 | O-RING |
900/30. | [1] | 140131-0021 | FLANGE BUSHING |
900/31. | [1] | 140271-0000 | BEARING PIN |
900/32. | [2] | 140118-0400 | O-RING |
Include in #1:
101401-1520
as _
Include in #2:
104205-2072
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
104205-2072
1900751012 KUBOTA
FUEL-INJECTION PUMP
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
104205-2072
1900751013 KUBOTA
FUEL-INJECTION PUMP
A K 23MB FUEL INJECTION PUMP PFR-2MD PFR
A K 23MB FUEL INJECTION PUMP PFR-2MD PFR
Information:
Start By:a remove rack actuator packageb. remove fuel injection pumps 1. Remove rack (1) from the fuel pump housing. 2. Remove six lifters (2) from the fuel pump housing. Put identification marks on the lifters for installation purposes. 3. Remove camshaft (3) from the fuel pump housing. It may be necessary to use a soft hammer to push the camshaft out of the governor end of the fuel pump housing. 4. Remove races (4) and bearing (5) from the camshaft. Remove ring (6) if necessary. 5. Remove rack bearing (7) from both ends of the housing and dowel (8) if necessary. 6. Use tooling (A), and remove three camshaft bearings (9). 7. Remove the bolts, cover (10) and the gasket. 8. Remove pins (12), the seal and dowels (11) if necessary. Pins (12) must be pushed from the inside out.Assemble Fuel Injection Pump Housing
1. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. 2. Lubricate the seal with clean engine oil, and install pin (12). Pin (12) must protrude into the pump bore 2.15 .05 mm (0.85 .002 in.).3. Install dowel (11) so that it protrudes into the pump bore 1.93 .05 mm (0.76 .002 in.). 4. Install the gasket, cover (10) and the bolts. 5. Install the rack bearing with tooling (B). Install the bearing until the driver comes in contact with the plate. The bearing should be installed to a depth of 83.0 0.5 mm (3.27 .02 in.) from the fuel pump mounting face. 6. Measure the rack bearing (7). Dimension (X) must be 11.178 0.05 mm (.4400 .002 in.). Dimension (W) must be 12.767 0.058 mm (.5026 .0022 in.). 7. Install dowel (8). Dowel (8) must protrude 6.0 0.5 mm (.24 .02 in.) from the fuel pump housing face.8. Install the rear rack bearing with tooling (C) to a depth of 7.16 0.13 mm (.282 .005 in.) below the fuel pump housing surface. The inside diameter of the rear rack bearing must be 12.746 0.045 mm (.5018 .0017 in.). 9. User tooling (D), and install three camshaft bearings (9). Oil holes (13) in the camshaft bearings must be positioned 30° 3° above the horizontal centerline toward the engine side of the fuel pump housing. The outer bearings must be installed 1.0 0.5 mm (0.04 0.02 in.) below the surface marked (Z). The inner bearing must be installed 218.0 0.3 mm (8.58 .012 in.) below the front surface (Y). Diameter (XX) must be 68.339 0.038 mm (2.6905 0.015 in.) after assembly. 10. Install ring (6) races (4) and bearing (5) on the camshaft. 11. Lubricate can bearings (9) and cam shaft bearing journals with clean engine oil.12. Install camshaft (3) into the fuel pump housing.
The notch on the lifter must be in line with the dowel in the lifter bore. The lifter must slide up and
1. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. 2. Lubricate the seal with clean engine oil, and install pin (12). Pin (12) must protrude into the pump bore 2.15 .05 mm (0.85 .002 in.).3. Install dowel (11) so that it protrudes into the pump bore 1.93 .05 mm (0.76 .002 in.). 4. Install the gasket, cover (10) and the bolts. 5. Install the rack bearing with tooling (B). Install the bearing until the driver comes in contact with the plate. The bearing should be installed to a depth of 83.0 0.5 mm (3.27 .02 in.) from the fuel pump mounting face. 6. Measure the rack bearing (7). Dimension (X) must be 11.178 0.05 mm (.4400 .002 in.). Dimension (W) must be 12.767 0.058 mm (.5026 .0022 in.). 7. Install dowel (8). Dowel (8) must protrude 6.0 0.5 mm (.24 .02 in.) from the fuel pump housing face.8. Install the rear rack bearing with tooling (C) to a depth of 7.16 0.13 mm (.282 .005 in.) below the fuel pump housing surface. The inside diameter of the rear rack bearing must be 12.746 0.045 mm (.5018 .0017 in.). 9. User tooling (D), and install three camshaft bearings (9). Oil holes (13) in the camshaft bearings must be positioned 30° 3° above the horizontal centerline toward the engine side of the fuel pump housing. The outer bearings must be installed 1.0 0.5 mm (0.04 0.02 in.) below the surface marked (Z). The inner bearing must be installed 218.0 0.3 mm (8.58 .012 in.) below the front surface (Y). Diameter (XX) must be 68.339 0.038 mm (2.6905 0.015 in.) after assembly. 10. Install ring (6) races (4) and bearing (5) on the camshaft. 11. Lubricate can bearings (9) and cam shaft bearing journals with clean engine oil.12. Install camshaft (3) into the fuel pump housing.
The notch on the lifter must be in line with the dowel in the lifter bore. The lifter must slide up and