Information fuel-injection pump
BOSCH
9 410 618 404
9410618404
ZEXEL
104205-2062
1042052062
KUBOTA
1754851012
1754851012

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104205-2062 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [2] | 140154-7720 | PLUNGER-AND-BARREL ASSY |
12. | [2] | 140110-4420 | DELIVERY-VALVE ASSEMBLY |
13. | [2] | 140112-2800 | COMPRESSION SPRING |
16. | [2] | 140115-2200 | GASKET D12.8&8.6T0.5 |
17. | [2] | 140116-7820 | FITTING |
20. | [2] | 140118-0500 | O-RING |
30. | [2] | 140131-0021 | FLANGE BUSHING |
31. | [2] | 140271-0000 | BEARING PIN |
32. | [4] | 140118-0400 | O-RING |
37. | [4] | 140124-0100 | FLAT-HEAD SCREW |
40. | [2] | 140200-2320 | TAPPET |
44. | [2] | 140212-0300 | BEARING PIN |
45. | [1] | 140213-0800 | LOCKING WASHER |
50. | [2] | 140215-2000 | COMPRESSION SPRING |
51. | [2] | 140216-1300 | SLOTTED WASHER |
52. | [2] | 140254-2900 | SLOTTED WASHER |
53/1. | [1] | 140254-1400 | PLATE T1.80 |
53/1. | [1] | 140254-1500 | PLATE T1.85 |
53/1. | [1] | 140254-1600 | PLATE T1.90 |
53/1. | [1] | 140254-1700 | PLATE T1.95 |
53/1. | [1] | 140254-1800 | PLATE T2.00 |
53/1. | [1] | 140254-1900 | PLATE T2.05 |
53/1. | [1] | 140254-2000 | PLATE T2.10 |
53/1. | [1] | 140254-2100 | PLATE T2.15 |
53/1. | [1] | 140254-2200 | PLATE T2.20 |
53/1. | [1] | 140254-2300 | PLATE T2.25 |
53/1. | [1] | 140254-2400 | PLATE T2.30 |
53/1. | [1] | 140254-2500 | PLATE T2.35 |
53/1. | [1] | 140254-2600 | PLATE T2.40 |
53/1. | [1] | 140254-2700 | PLATE T2.45 |
53/1. | [1] | 140254-2800 | PLATE T2.50 |
53/1. | [1] | 140254-3100 | PLATE T1.825 |
53/1. | [1] | 140254-3200 | PLATE T1.875 |
53/1. | [1] | 140254-3300 | PLATE T1.925 |
53/1. | [1] | 140254-3400 | PLATE T1.975 |
53/1. | [1] | 140254-3500 | PLATE T2.025 |
53/1. | [1] | 140254-3600 | PLATE T2.075 |
53/1. | [1] | 140254-3700 | PLATE T2.125 |
53/1. | [1] | 140254-3800 | PLATE T2.175 |
53/1. | [1] | 140254-3900 | PLATE T2.225 |
53/1. | [1] | 140254-4000 | PLATE T2.275 |
53/1. | [1] | 140254-4100 | PLATE T2.325 |
53/1. | [1] | 140254-4200 | PLATE T2.375 |
53/1. | [1] | 140254-4300 | PLATE T2.425 |
53/1. | [1] | 140254-4400 | PLATE T2.475 |
53/1. | [1] | 140254-4500 | PLATE T2.525 |
60. | [1] | 140243-3620 | CONTROL ROD |
65. | [1] | 140262-0401 | PLATE |
66. | [4] | 140252-0001 | FLAT-HEAD SCREW |
77. | [2] | 140241-4021 | CONTROL SLEEVE |
93. | [1] | 140402-3020 | EYE BOLT |
93/1. | [1] | 140402-3000 | EYE BOLT |
93/2. | [2] | 026510-1340 | GASKET D13.4&10.2T1 |
93/3. | [1] | 140420-2400 | BLEEDER SCREW |
93/4. | [1] | 026506-1040 | GASKET D9.9&6.2T1 |
900. | [2] | 140191-0820 | PLUNGER-AND-BARREL ASSY |
900/5. | [1] | 140154-7720 | PLUNGER-AND-BARREL ASSY |
900/12. | [1] | 140110-4420 | DELIVERY-VALVE ASSEMBLY |
900/13. | [1] | 140112-2800 | COMPRESSION SPRING |
900/16. | [1] | 140115-2200 | GASKET D12.8&8.6T0.5 |
900/17. | [1] | 140116-7820 | FITTING |
900/20. | [1] | 140118-0500 | O-RING |
900/30. | [1] | 140131-0021 | FLANGE BUSHING |
900/31. | [1] | 140271-0000 | BEARING PIN |
900/32. | [2] | 140118-0400 | O-RING |
Include in #1:
101606-6360
as _
Include in #2:
104205-2062
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
104205-2062
1754851012 KUBOTA
FUEL-INJECTION PUMP
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
104205-2062
1754851013 KUBOTA
FUEL-INJECTION PUMP
A K 23MB FUEL INJECTION PUMP PFR-2MD PFR
A K 23MB FUEL INJECTION PUMP PFR-2MD PFR
104205-2062
1754851012 KUBOTA
FUEL-INJECTION PUMP
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
K 23MB FUEL INJECTION PUMP PFR-2MD PFR
Information:
1. Remove wiring harnesses from bracket (1). 2. Disconnect the wires at connections (5) Remove line (4). Remove five bolts (2), bracket (1) cover (3) and the gasket. 3. Remove two bolts (6) and clamps. Remove rack solenoid. (7) 4. Disconnect wires at connections (8). Remove two bolts (10) and bracket assembly (9). Loosen the locknut and remove rack position sensor (11). Be careful not to lose the spring that is around the sensor. To remove the transducer module at this time use the following procedure.a. disconnect wires at connector (8)b. remove the connector from the wiresc. remove four bolts that fasten transducer module (22) to housing (15)d. feed the wires through housing (18) while removing the transducer module. 5. Remove three bolts (12) from inside housing (14). Remove two bolts (13) and remove housing (14). 6. Loosen locknut (15) and remove engine speed sensor (16). 7. Remove seven bolts (17) and remove the transducer module and housing (18). 8. Remove three bolts (19) and cover (20). 9. Remove two bolts (21). Remove transducer module (22) and gasket. 10. Remove lockring (27), seat (25), spring (24), sleeve (23) and lockring (26). 11. Remove three bolts (28) and remove cylinder (29). 12. Remove sleeve (30), piston (31) and valve (32). Remove O-ring seal (33) from sleeve (30). 13. Remove bolts (34) and remove retainer (35). Remove two races and one bearing (not shown).Assemble Rack Actuator Package
1. Lubricate bearing (37) with engine oil. Install race (36), bearing (37), race (36) and retainer (35) on the fuel injection pump camshaft. 2. Lubricate O-ring seal (33) with engine oil and install on sleeve (30). Install sleeve (32) and piston (31) into sleeve (33). 3. Install sleeve (30) into cylinder (29).4. Install lockring (26), sleeve (23), spring (24), seat (25) and lockring (27) on valve (32). 5. Put cylinder assembly (29) in position on the fuel injection pump housing with piston (31) engaged over fuel injection pump rack (38). Be sure that rack (38) is properly engaged with piston (31). 6. Fasten cylinder (29) to the fuel injection pump housing with three bolts (28). The rack and servo valve (32) must move freely after bolts (28) are tight. 7. Install gasket (39) and transducer module (22) on housing (18). 8. Place wire harness (40) in the slot of the housing. 9. Install cover (20) and bolts (19). 10. Install the gasket and housing (18) on the fuel injection pump housing with seven bolts (17). 11. Install engine speed sensor (16) until it contacts retainer (35). Back the engine speed sensor out (counterclockwise) 180°. This procedure will provide a clearance of .76 mm (.030 in). Tighten locknut (15) to a torque of 13 2 N m (10 1 lb.ft.). 12. Install gasket and housing (14).13. Install the rack position sensor damping seal in housing (14). Install the spring and rack position sensor (11) in housing (14). 14. Connect the rack position sensor wiring connector to the transducer module wiring connector (P8 to
1. Lubricate bearing (37) with engine oil. Install race (36), bearing (37), race (36) and retainer (35) on the fuel injection pump camshaft. 2. Lubricate O-ring seal (33) with engine oil and install on sleeve (30). Install sleeve (32) and piston (31) into sleeve (33). 3. Install sleeve (30) into cylinder (29).4. Install lockring (26), sleeve (23), spring (24), seat (25) and lockring (27) on valve (32). 5. Put cylinder assembly (29) in position on the fuel injection pump housing with piston (31) engaged over fuel injection pump rack (38). Be sure that rack (38) is properly engaged with piston (31). 6. Fasten cylinder (29) to the fuel injection pump housing with three bolts (28). The rack and servo valve (32) must move freely after bolts (28) are tight. 7. Install gasket (39) and transducer module (22) on housing (18). 8. Place wire harness (40) in the slot of the housing. 9. Install cover (20) and bolts (19). 10. Install the gasket and housing (18) on the fuel injection pump housing with seven bolts (17). 11. Install engine speed sensor (16) until it contacts retainer (35). Back the engine speed sensor out (counterclockwise) 180°. This procedure will provide a clearance of .76 mm (.030 in). Tighten locknut (15) to a torque of 13 2 N m (10 1 lb.ft.). 12. Install gasket and housing (14).13. Install the rack position sensor damping seal in housing (14). Install the spring and rack position sensor (11) in housing (14). 14. Connect the rack position sensor wiring connector to the transducer module wiring connector (P8 to