104204-2000 ZEXEL 9 410 617 717 BOSCH FUEL-INJECTION PUMP 9410617717 1042042000


 

Information fuel-injection pump

BOSCH 9 410 617 717 9410617717
ZEXEL 104204-2000 1042042000
104204-2000 FUEL-INJECTION PUMP
Rating:
64
Buy FUEL-INJECTION PUMP 104204-2000 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104204-2000
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105148-1210
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 11.8{120}
10. NOZZLE-HOLDER 105078-0100
11. NOZZLE 105007-1170

Scheme ###:

5. [2] 140154-8020 PLUNGER-AND-BARREL ASSY
12. [2] 140110-3620 DELIVERY-VALVE ASSEMBLY
13. [2] 140112-2800 COMPRESSION SPRING
16. [2] 140115-2200 GASKET D12.8&8.6T0.5
17. [2] 140116-7220 FITTING
20. [2] 016550-1220 O-RING
30. [2] 140131-0021 FLANGE BUSHING
31. [2] 140271-0000 BEARING PIN
32. [4] 016550-1620 O-RING
37. [4] 140124-0100 FLAT-HEAD SCREW
40. [2] 140200-2320 TAPPET
44. [2] 140212-0300 BEARING PIN
45. [1] 140213-0800 LOCKING WASHER
50. [2] 140215-2000 COMPRESSION SPRING
51. [2] 140216-1300 SLOTTED WASHER
52. [2] 140254-2900 SLOTTED WASHER
53/1. [1] 140254-1400 PLATE T1.80
53/1. [1] 140254-1500 PLATE T1.85
53/1. [1] 140254-1600 PLATE T1.90
53/1. [1] 140254-1700 PLATE T1.95
53/1. [1] 140254-1800 PLATE T2.00
53/1. [1] 140254-1900 PLATE T2.05
53/1. [1] 140254-2000 PLATE T2.10
53/1. [1] 140254-2100 PLATE T2.15
53/1. [1] 140254-2200 PLATE T2.20
53/1. [1] 140254-2300 PLATE T2.25
53/1. [1] 140254-2400 PLATE T2.30
53/1. [1] 140254-2500 PLATE T2.35
53/1. [1] 140254-2600 PLATE T2.40
53/1. [1] 140254-2700 PLATE T2.45
53/1. [1] 140254-2800 PLATE T2.50
53/1. [1] 140254-3100 PLATE T1.825
53/1. [1] 140254-3200 PLATE T1.875
53/1. [1] 140254-3300 PLATE T1.925
53/1. [1] 140254-3400 PLATE T1.975
53/1. [1] 140254-3500 PLATE T2.025
53/1. [1] 140254-3600 PLATE T2.075
53/1. [1] 140254-3700 PLATE T2.125
53/1. [1] 140254-3800 PLATE T2.175
53/1. [1] 140254-3900 PLATE T2.225
53/1. [1] 140254-4000 PLATE T2.275
53/1. [1] 140254-4100 PLATE T2.325
53/1. [1] 140254-4200 PLATE T2.375
53/1. [1] 140254-4300 PLATE T2.425
53/1. [1] 140254-4400 PLATE T2.475
53/1. [1] 140254-4500 PLATE T2.525
60. [1] 140243-6120 CONTROL ROD
65. [1] 140262-1100 PLATE
66. [4] 140252-0000 FLAT-HEAD SCREW
77. [2] 140241-4021 CONTROL SLEEVE
93. [1] 140402-3520 EYE BOLT
110. [1] 140420-2400 BLEEDER SCREW
111. [1] 026506-1040 GASKET D9.9&6.2T1

Include in #1:

Include in #2:

104204-2000 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104204-2000 
104204-2001 
9 410 617 717 
   
FUEL-INJECTION PUMP
* K 23MB PFR-2MD PFR




Information:

(1) Bore in rocker arm for shaft ... 24.803 0.013 mm (.9765 .0005 in) Diameter of rocker arm shaft ... 24.752 0.013 mm (.9745 .0005 in)(2) Put 5P3931 Anti-Seize Compound on all the threads of bolts that hold rocker arm shafts and tighten the bolts in the step sequence that follows:Step 1. Tighten bolts from 1 through 6 in number sequence to ... 270 27 N m (200 20 lb ft)Step 2. Tighten bolts from 1 through 6 in number sequence to ... 450 20 N m (330 15 lb ft)Step 3. Tighten bolts from 1 through 6 in number sequence again to ... 450 20 N m (330 15 lb ft) (3) Torque for locknut for valve adjustment screw ... 30 4 N m (22 3 lb ft)(4) Torque for locknut for bridge assembly ... 30 4 N m (22 3 lb ft)Bridge Installation Instructions:a. Lubricate bridge dowel, bridge bore and top pad of bridge with engine oil.b. Install bridge assembly on bridge dowel.c. While firmly pressing [0.5 to 4.5 kg (1 to 10 lb)] straight down on the bridge pad, turn the adjusting screw clockwise until contact is made with the valve stem.d. Turn the screw clockwise and additional 20 to 30° (1/3 to 1/2 of 1 hex on nut) to straighten the dowel in the guide and compensate for slack in the threads.e. Hold the adjusting screw in this position and tighten the locknut to a torque of 30 4 N m (22 3 lb ft).(5) Valve clearance (with engine stopped). Intake valves ... 0.38 mm (.015 in)Exhaust valves ... 0.76 mm (.030 in) After setting valve clearance, tighten adjusting screw locknut to a torque of 30 4 N m (22 3 lb ft). Then, recheck the valve clearance.(5) Clearance for valves: Intake valves ... 0.38 mm (.015 in)Exhaust valves ... 0.76 mm (.030 in)(6) Height to top of dowel ... 53.3 0.5 mm (2.10 .02 in)(7) Diameter of dowel ... 11.008 0.003 mm (.4334 .0001 in) Bore in bridge for dowel ... 11.13 0.05 mm (.438 .002 in)Bore in head for dowel ... 10.968 0.020 mm (.4318 .0008 in) (8) Diameter of valve lifter ... 27.896 0.013 mm (1.0983 .0005 in) Bore in block for valve lifter ... 27.953 0.019 mm (1.1005 .0008 in) See Guideline For Reusable Parts; Salvage Of Lifter Bores In 3400 Family Engines, Form No. SEBF8069 for the procedure, tooling and specifications needed to install 4W4588 Sleeves for salvage of the lifter bores in the cylinder block.(9) 6N6872 Lifter Guide Spring. See Guideline For Reusable Parts, Form No. SEBF8066, for information on using guide springs again. (10) 2N7229 Spring: Length under test force ... 74.2 mm (2.92 in)Test force ... 45 to 53 N (10 to 12 lb)Free length after test ... 114.3 mm (4.50 in)Outside

Have questions with 104204-2000?





Group cross 104204-2000 ZEXEL

104204-2000  

104204-2001 
9 410 617 717 
 
FUEL-INJECTION PUMP

Ishikawajima-S 

9 410 618 346 
NP-PFR2MD45/2NP1 
131017620 
FUEL-INJECTION PUMP
Back to top