Buy 09500-05273 INJECTOR ASSY Denso Cross


 

Information injector assy

09500-05273 INJECTOR ASSY
Rating:
34
Buy INJECTOR ASSY 09500-05273 genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$252.92

05 Jan 2025

KR: Adabus
095000-527# 095000-5270 Common Rail Fuel Injector Assembly 095000-5271 Injector Nozzle 095000-5273 for Hino 23670-E0250
Generic
$2,509.79

28 Dec 2024

CN: QYWD
6X Fuel Injector Model 095000-5273 0950005273 for Hino J08E Engine
TUWODE Part Number: 095000-5273 950005273 || Item Type: Fuel Injector || Applicable Models: Fit for Hino J08E Engine || Well-functioning fuel injectors ensure the correct air-fuel ratio, which is essential for minimizing harmful emissions. || Fuel is broken into fine droplets for optimal air mixing and enhanced combustion efficiency.
$261.90

28 Dec 2024

CN: QINGCANG Constructio
Qiape Fuel Injector for HINO J08E Engine 095000-5273 0950005273
Qiape Part Name:Fuel Injector 095000-5273 0950005273 || Part Number:095000-5273 0950005273 || APPlication: Compatible with HINO J08E Engine || Please tell us of your engine model or a view of nameplate when order this item to lower the error rate Thanks || There are no instructions included in this kit it is recommended to install professionally

Include in #3:

Number on scheme 000
INJECTOR ASSY
09500-05270 as INJECTOR ASSY

Cross reference number



Part num Firm num Firm Name
09500-05273    INJECTOR ASSY




Information:

1. Remove suction bell (3) and tubes, oil supply tube (2) and BrakeSaver oil supply tube (1) from the engine block and oil pump. 2. Remove three bolts (5) and oil pump (4) from the engine. The following steps are for installation of the oil pump.3. Put oil pump (4) in position on the engine. Make sure the oil pump gear is engaged with the crankshaft gear, and install three bolts (5) that hold the oil pump.4. Put clean engine oil on the O-ring seals on the oil tubes.5. Install suction bell (3) and tubes, oil supply tube (2) and the BrakeSaver oil supply tube (1).END BY:a. install oil pan (BrakeSaver)Disassemble Oil Pump (BrakeSaver)
START BY:a. remove oil pump (BrakeSaver) 1. Remove the bolt and washer that hold drive gear (1) on the shaft.2. Use tooling (A) to remove drive gear (1) from the shaft. Remove the key from the shaft. Put alignment marks on the pump bodies so they can be assembled in the correct position. 3. Remove retainer (3) for the bypass valve. Remove the spring and bypass valve.4. Remove bolts (4) that hold pump body (2) to the main pump body. Remove pump body (2).5. Use tooling (B) to remove the bearings from pump body (2). 6. Remove gears (7). Put identification marks on the gears so they can be assembled in the same position.7. Remove spacer (6) from main oil pump body (5). Use tooling (B) to remove the bearings from spacer (6).8. Remove the gears from main oil pump body (5). 9. Use tooling (B) to remove the bearings from the main oil pump body.Assemble Oil Pump (BrakeSaver)
1. Use tooling (A) to install bearings (2) until they are even with the outside surface of main oil pump body (1). Install bearings (2) so the joints in the bearings are 30° 15° from the center line of the bearing bores and toward the oil pump outlet passage as shown. 2. Use tooling (A) to install bearings (3) in the spacer. Install the bearings until they are in position an equal distance in from each side of the spacer. Install the bearings with the oil holes in the bearings in alignment with the oil holes in the spacer and the joints in the bearings in alignment with the cavity on the spacer as shown. 3. Put clean engine oil on all the gears and bearings before they are assembled in the oil pump. Install idler and drive gears (5) in the main oil pump body.4. Install spacer (4) on the gear shafts with the smaller cavity out and the oil holes in the spacer toward the pump outlet passage as shown. 5. Use tooling (A) to install bearings (6) in pump body (7) until they are 1.52 0.25 mm (.060 .010 in.) from the inside edge of the bearing bores. Install the bearings so the joints in the bearings are 30° 15° from the center line of the bearing bores and toward

Have questions with 09500-05273?





Group cross 09500-05273

Back to top