Buy 09340-00340 NOZZLE ASSY Denso Cross


 

Information nozzle assy

ZEXEL 105000-1640
BOSCH 9432610156
Nozzle Type: ND-DN0S34
ISHIKAWAJIMA INDUSTRIAL LED110
ISHIKAWAJIMA INDUSTRIAL LED35
MITSUBISHI INDUSTRIAL AD105
MITSUBISHI INDUSTRIAL D65,D75
MITSUBISHI INDUSTRIAL KE100
MITSUBISHI INDUSTRIAL KE130
MITSUBISHI INDUSTRIAL KE135
MITSUBISHI INDUSTRIAL KE250
MITSUBISHI INDUSTRIAL KE250-53M
MITSUBISHI INDUSTRIAL KE70
MITSUBISHI INDUSTRIAL KE80,KE135
MITSUBISHI INDUSTRIAL KE85
MITSUBISHI INDUSTRIAL KE95
MITSUBISHI INDUSTRIAL M11,M85,M95
MITSUBISHI INDUSTRIAL M14
MITSUBISHI INDUSTRIAL M4,M5
MITSUBISHI INDUSTRIAL M7
MITSUBISHI INDUSTRIAL NM6
MITSUBISHI INDUSTRIAL SD10
MITSUBISHI INDUSTRIAL SD3H
MITSUBISHI INDUSTRIAL SD4
MITSUBISHI INDUSTRIAL SD5
MITSUBISHI INDUSTRIAL SD6
MITSUBISHI INDUSTRIAL SD8
MITSUBISHI INDUSTRIAL SDT130
MITSUBISHI INDUSTRIAL SDT90
09340-00340 NOZZLE ASSY
Rating:
19
Buy NOZZLE ASSY 09340-00340 genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

15 Jan 2025

Fuel Injector Nozzle DN0S34 093400-0340 for Mitsubishi M11 (6) Pieces/Lot
Generic
$71.75
 

21 Feb 2022
0.88[0.40] Pounds
CN: china lutong part pl
Fuel Injector Nozzle Tips DNOS34 093400-0340 105000-1640 fits Mitsubishi M11 6pcs/lot
DICSCL PARCS Fuel Injector Nozzle Tips DNOS34 093400-0340 105000-1640 fits Mitsubishi M11 6pcs/lot || Material: Made of high quality for longer durability and strength.100% quality inspection to ensure the high quality. Upgraded packaging to avoid damage. || Easy Installation:No further modification to direct replacement. || OEM Part Number:DNOS34/093400-0340/105000-1640 || Estimated Time of Delivery from China: 5-10 working days.Customer satisfaction is always our top priority, we are standing by ready to provide you with reliable assistance with any questions you may have

Cross reference number



Part num Firm num Firm Name
09340-00340  09340-0034  NOZZLE ASSY
131416070    ISHIKAWAJIMA NOZZLE ASSY
09340-00340    MITSUBISHI NOZZLE ASSY
MM300151    MITSUBISHI NOZZLE ASSY




Information:


REMOVING CONNECTING ROD BEARING CAP4. Push the piston and connecting rod upward until the piston rings clear the cylinder block. Remove the piston and connecting rod from the cylinder block.
REMOVING PISTON
Do not allow the connecting rods to hit the bottom edge of the cylinder bores or crankshaft journals when removing or installing. Check the lower portion of the bores for burrs or scratches. Use crocus cloth to remove any burrs or scratches from bottom edge of the bores.
5. Keep the connecting rod bearing cap with its respective connecting rod and piston.6. Repeat Steps 2 through 5 for the remaining pistons.Install Pistons
1. Rotate the crankshaft to position bearing journal of the piston to be installed.2. Lubricate the crankshaft bearing journal, bore in cylinder block, piston, rings, and connecting rod bearings with clean engine oil (SAE 30).3. Install a 1Y7426 Ring Compressor (3), or the 4S9450 Compressor (1) and the 4S9446 Clamp (2) from the 4S9458 Teflon Seal Tool Group, on the piston to compress the rings. Install the piston and connecting rod in cylinder bore with piston crater toward vee of engine. Guide the lower end of connecting rod over the crankshaft journal to prevent damage to the crankshaft.
INSTALLING PISTON
1. 4S9450 Compressor. 2. 4S9446 Clamp.
INSTALLING PISTON ALTERNATE METHOD
3. 1Y7426 Ring Compressor.4. Install the connecting rod cap to connecting rod so numbers correspond and both numbers appear on the same side. Lubricate bolt threads, seating faces of cap and nuts, install the retaining nuts and tighten to 30 3 lb. ft. (4.1 0.4 mkg). Mark cap and nut with matching marks. Tighten additional from mark 60° 5°.5. Repeat Steps 1 thru 4 for the remaining pistons.Disassemble Piston
PISTON ASSEMBLY1. Use ring expander (1) to remove rings.
REMOVING RINGS
1. 5F9059 Ring Expander.2. Remove snap ring (5) and push piston pin (2) out of piston (4) and connecting rod (3).
PISTON DISASSEMBLED
2. Piston pin. 3. Connecting rod. 4. Piston. 5. Snap ring.Assemble Piston
1. Install connecting rod into piston with boss on rod on same side as crater in piston crown.
CONNECTING ROD AND PISTON
CONNECTING ROD AND PISTON Installation of connecting rods WITHOUT BOSS on rod; Install connecting rod into piston with cylinder identification number (as marked on the lower end of the rod and on the cap) 180° opposite the crater in piston crown.2. Install piston pin and snap rings.3. Use the 8S2304 Piston Ring Groove Cleaner to clean the piston ring grooves before installing piston rings.4. Install oil ring spring (6) before installing oil ring.
8S2304 RING GROOVE CLEANER
INSTALLING OIL RING SPRING
6. Oil ring spring.5. Use a 5F9059 Ring Expander to install piston rings. Install compression ring with side marked "TOP" toward top of piston. Install oil ring with gap 180° from oil ring spring joint and approximately 120° from compression ring gap.

Have questions with 09340-00340?





Group cross 09340-00340

Back to top