029010-6550 ZEXEL 9 442 611 252 BOSCH BLEEDER SCREW 9442611252 0290106550 1157296830


 

Information bleeder screw

BOSCH 9 442 611 252 9442611252
ZEXEL 029010-6550 0290106550
ISUZU 1157296830 1157296830
029010-6550 BLEEDER SCREW
Rating:
35
Buy BLEEDER SCREW 029010-6550 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

Cross reference number

Zexel num
Bosch num
Firm num
Name
029010-6550 
9 442 611 252 
1157296830  ISUZU
BLEEDER SCREW
D 90HY BOLT Standard parts Others
029010-6550 
9 442 611 252 
6073135370  HINO
BLEEDER SCREW
D 90HY BOLT Standard parts Others
029010-6550 
9 442 611 252 
6073137270  HINO
BLEEDER SCREW
A D 90HY BOLT Standard parts Others
029010-6550 
9 442 611 252 
ME748432  MITSUBISHI
BLEEDER SCREW
D 90HY BOLT Standard parts Others
029010-6550 
9 442 611 252 
901430695071  TOYOTA-INDUST
BLEEDER SCREW
D 90HY BOLT Standard parts Others




Information:

Start By:a. remove valve covers1. Turn the flywheel with Tool (C) until there is clearance between the rocker arms and valve bridges. 2. Engage Tool (A) with the rocker arm, and move Tool (A) against the valve spring force until push rod (1) can be removed.3. Remove the other push rod for the same cylinder. Mark each push rod so it can be installed in its original position. 4. Use Tool (B) to remove valve lifter (2).5. Remove the other valve lifter for the same cylinder. Mark each valve lifter so it can be installed in its original position. 6. Remove spring (3) from lifter (2).7. Inspect spring (3). See Guideline For Reusable Parts, SEBF8066. 8. Identify the location of each valve bridge (4), then remove them.Install Push Rods, Valve Lifters & Valve Bridges
1. Put clean engine oil on each bridge dowel and the bore of each bridge. Install bridges (1) in their original position.2. Use the following procedure to adjust the valve bridges.a. Put clean SAE 30 Engine Oil in the lubrication passage of the bridge.b. Press straight down on the top contact surface of the bridge with a force of 4.45 to 44.50 N (1 to 10 lb).c. Turn the adjusting screw clockwise until the oil film in the lubrication passage of the bridge moves inward.d. Turn the adjusting screw an additional 20 to 30 degrees (1/3 to 1/2 of a flat on the hex nut).e. Hold the adjusting screw in position, and tighten the locknut to a torque of 26 to 34 N m (19 to 25 lb ft).f. Do this procedure for both bridges. Put clean engine oil on the top contact surface of both bridges. 3. Install spring (3) on valve lifter (2). 4. Fasten Tool (A) to valve lifter (2).5. Immerse valve lifter (2) in clean engine oil; then install it in its original position.6. Install the other valve lifter for the same cylinder. 7. Engage Tool (B) with the rocker arm, and move Tool (B) against the valve spring force until push rods (4) can be installed in their original position.8. Use Tool (C) to turn the flywheel so the remaining push rods can be installed. Be sure there is clearance at the rocker arms and valve bridges before compressing the valve pump.9. Check the valve clearance settings. The clearance for the intake valves is 0.38 mm (.015 in). The clearance for the exhaust valve is 0.76 mm (.030 in). See the topic "Valve Clearance Setting" in Testing & Adjusting.End By:a. install valve covers

Have questions with 029010-6550?





Group cross 029010-6550 ZEXEL

Isuzu 

029010-6550  
9 442 611 252 
1157296830 
BLEEDER SCREW

Hino 

029010-6550  
9 442 611 252 
6073135370 
BLEEDER SCREW
029010-6550  
9 442 611 252 
6073137270 
BLEEDER SCREW

Mitsubishi 

029010-6550  
9 442 611 252 
ME748432 
BLEEDER SCREW

Toyota-Indust 

029010-6550  
9 442 611 252 
901430695071 
BLEEDER SCREW
Back to top